Asko D3432XL Instrukcja obsługi i konserwacji - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Zmywarka Asko D3432XL. Asko D3432XL 16 stron. Asko dishwasher use and care d3432

Drukuj stronę

WER BUTT

POWER BUTT

WER BUTT

WER BUTTON

Use this button to turn the main power to the unit

on and off. The location of the power button is

illustrated on page 7.

STAR

ART/ST

T/STOP BUTT

T/ST

OP BUTTON

OP BUTT

Once you have selected the wash program and

temperature and drying options, press this button then

close the door to start the dishwasher. (Make sure the

door is securely closed.)

INTERR

INTERRUPTING

INTERR

UPTING A PR

UPTING

INTERR

UPTING

ADD AN ITEM

If you want to interrupt a program to add an item, open

the door slightly until the spray arms stop turning. You

can then open the door fully and place the item into the

dishwasher. Close the door securely. The program will

continue from where it was interrupted.

WARNING!

Be extremely careful when opening the door during

a program. The water is hot and you could get

scalded.

CHANGING OR STOPPING

CHANGING OR ST

OGRAM

PROGRAM

OGRAM

If you decide to change the program after you have started

the machine, press the Start/Stop button for three

seconds. You will have to select the program and options

again when you are ready to restart the program. (Note:

If the program has already gone through the wash cycle,

you will have to add detergent.)

PROGRAM

OGRAM

OGRAM TIMES

OGRAM

TIMES

OGRAM

TIMES

The program times may not always be the same

because of variations in the household hot water

temperature. The dishwasher heats the water to the

proper temperature for the program selected; so if the

temperature of the water entering the dishwasher is

too low, the dishwasher will run longer because it takes

longer to heat the water. Raising your water heater

setting could help to shorten the cycle times.

F F F F F A A A A A UL

ULT MESSA

T MESSA

T MESSAGES

T MESSA

GES

In the event that the machine should fail during a

program, the control panel lights will flash to indicate an

operation fault has occurred. The table below defines

these signals and gives possible causes and solutions.

See also "Troubleshooting" on page 12.

Flashing Indicator Light(s)

Heavy Wash

Delicate Wash

Quick Wash

Pots and Pans and Heavy Wash

Pots and Pans and Normal Wash

Page 8

A PROGRAM

A PR

OGRAM T T T T T O O O O O

OGRAM

A PR

OGRAM

OPPING

OPPING A A A A A

OPPING

Type of Fault and Recommended Action

Too much water has entered the dishwasher. Call a service technician.

Water inlet fault. Make sure the water supply is open.

Valve leakage. Shut off the water supply and contact a service technician.

The drain is blocked. See "Troubleshooting" on page 12.

The filter is clogged. See "Cleaning the Filters" on page 9.

CHILD-SAFE

FEA

FEATURE

FEA

TURE

FEA

TURE

As a safety measure, Model D3432 can be programmed

not to start unless the Temperature and Drying buttons

are held down simultaneously. To program this feature,

follow the steps below:

1. Turn off the power to the machine.

2. Simultaneously press and hold down the

Temperature and Drying buttons as you turn on the

power to the machine. The Temperature, Drying and

Start buttons will flash.

3. Release the buttons.

4. Press the Program button. The Pots and Pans

button will glow to indicate the button lock is activated.

5. Press Start to confirm your selection and return to

the main menu.

Once the child-safe feature is active, the Temperature

and Dry buttons will flash whenever you press any of

the buttons. To deactivate the button lock, press the

Temperature and Dry buttons simultaneously . You can

then select the program and options and press Start to

start the unit. The lock will reactivate automatically in

three minutes.

To permanently deactivate the button lock, repeat the

steps above. The Pots and Pans button will go out to

indicate the button lock is off.

END-OF-PR

END-OF-PROGRAM SIGN

END-OF-PR

OGRAM SIGN

OGRAM SIGNAL

OGRAM SIGN

END-OF-PR

OGRAM SIGN

Model D3432 can be programmed to emit a short signal

when the program is finished. To program this feature,

follow the steps below:

1. Turn off the power to the machine.

2. Press and hold down the Delay Start button as you

turn on the power to the machine. The Delay Start

button will flash.

3. Release the button.

4. Press the Program button. The Pots and Pans

button will glow to indicate the end-of-program

signal is activated.

5. Press Start to confirm your selection and return to

the main menu.

To deactivate the signal, repeat these steps. The Pots

and Pans button will go out to indicate the signal is off.

If you have corrected the fault, turn the main power off

then back on to remove the fault indication. If it still

displays, try again to correct the problem or call a service

technician.

BUTT

UTTON

UTT