Asko T731 Instrukcja obsługi i konserwacji - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Suszarka Asko T731. Asko T731 20 stron. User manual use & care guide fr
Również dla Asko T731: Skrócona instrukcja obsługi (2 strony), Podręcznik planowania i projektowania (19 strony), Instrukcja obsługi i konserwacji (20 strony), (Hiszpański) Instrukcja obsługi i konserwacji (20 strony), (Francuski) Podręcznik użytkowania i konserwacji (20 strony)
Drukuj stronę
INSTALLATION INSTRUCTIONS
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
SPECIFICATIONS
Height
33-1/2"–34-1/2 (850–876 mm)
Width
23-7/16" (595 mm)
Plus exhaust duct connection
Depth
23-7/16" (595 mm)
Weight
86 lbs (39 kg)
Drum material
Stainless Steel
Outer casing
Stove-enamelled hot-dipped
galvanized steel
CONNECTING THE EXHAUST DUCT TO THE DRYER
NOTE: You will need to purchase a UL-CSA-approved
4-inch ridged metal exhaust duct.
The dryer is delivered with the stub pipe attached to the
rear exhaust outlet, but the exhaust duct can be attached
to either the right or left exhaust outlet.
ASKO dryers have a
"T-style" exhaust vent
that allows you to
connect the duct on the
rear or on the left or
right side.
Side Exhaust Outlet
CONNECTING THE EXHAUST DUCT TO
THE REAR OUTLET
To connect the exhaust duct to the rear outlet, follow the
steps below:
1. Push the duct onto the stub pipe and secure it with a
clamp.
2. With the duct attached, insert the stub pipe into the
hole. It should snap into place.
3. After you push the dryer into place, check for kinks in
the duct.
Page 4
Rear Exhaust Outlet
Stub
Clamp
Duct
(not supplied)
NOTE: Cosmetic damage must be reported to your
dealer within five days from the date of
purchase. After unpacking the dryer, thoroughly
check the unit for cosmetic damage.
Power requirement
2800 watts
For connection
Single-phase, 230 V, 30 Amp
Internal fuse
15 amp.
Heating element
2500 watts
NOTE: Excessive duct length and too many bends can
impede drying performance. We recommend
that you cut off any excess exhaust duct and run
the duct with as few bends as possible. Make
any necessary bends as gentle as possible.
NOTE: Maximum duct length of 15 feet, using two 90°
elbows is allowed. Subtract 4 feet of duct for
each additional elbow.
CONNECTING THE EXHAUST DUCT TO
THE LEFT OR RIGHT SIDE OUTLET
To connect the exhaust duct to the left or right side outlet,
follow the steps below:
1. Using a flathead screw-driver, turn the exhaust outlet
cover you plan to use to the right or left to align the
tabs holding the cover in place.
2. Remove the exhaust outlet cover.
3. Remove the stub pipe from the rear exhaust outlet
and place it in the outlet you plan to use.
4. Push the duct onto the stub pipe and secure it with a
clamp.
5. With the duct attached, insert the stub pipe into the
hole. It should snap into place.
6. After you push the dryer into place, check for kinks in
the duct.
7. Use the exhaust outlet cover you removed from the
to cover the rear exhaust outlet.
WARNING!
To reduce the risk of fire, this appliance must be
exhausted OUTDOORS or the equivalent.
Never cover the end of the dryer stub or exhaust duct
with anything to catch lint, except for UL approved
vent basket.