Ambirad AR35/33' SL Manual de instalação e manutenção - Página 7
Procurar online ou descarregar pdf Manual de instalação e manutenção para Aquecedor a gás Ambirad AR35/33' SL. Ambirad AR35/33' SL 20 páginas. Gas fired radiant tube heaters
- 1. Table of Contents
- 2. AR and ARE Series Gas Fired
- 3. Gas Connection
- 4. Standards
- 5. Assembly Instructions
- 6. Fitting Reflectors and End Caps
- 7. Burner/Fan/Damper Assembly
- 8. AR and ARE Series Double Linear
- 9. HB and DL Damper Settings
- 9. Installation – Suggested Methods
- 9. Of Heater Suspension
- 10. Flue Connection
- 11. Commissioning for Individually
- 12. Routine Service
- 13. Trouble Shooting Checklist
- 14. User Instructions for Ambi-Rad
Insert stainless steel tube into the first two
suspension brackets (on some tube lengths
the stainless steel tube section may fall
short of the second bracket).
Note The stainless steel section is at the
burner end of the heater.
Insert the remaining mild steel tube(s)
into the remaining brackets to make the
overall tube length. Tube sections are
attached to each other by means of two
'grub screws' and locking nuts.
Note Do not over tighten the grub screws
into the mild steel tube. Finger-tight is
sufficient to allow for thermal expansion,
but locking nuts must be tightened with a
spanner.
When all tubes are connected together, turn
the tube assembly so the collar screws and
nuts are facing left to right when viewed
from the top. Push the turbulator into the
end of the tube which is furthest away from
where the burner will be located (same end
as fan/damper), ensuring it is fully inserted
to the location tabs at the end of the
turbulator.
Note Fit reflector end-caps before fitting
burner assembly and fan assembly. (Not ARE)
Fit the fan/damper assembly onto the mild
steel tube (opposite end to where the burner
will be located), ensuring it is fully engaged.
Secure the pinch screws provided.
Note The above assembly instructions apply
to ARE SL/HB series of heaters. However,
turbulators are not supplied.
8 Fitting reflectors and end caps
Remove the plastic film from the reflectors.
Note The reflectors are punched at one end.
These holes coincide with the Type 'A'
suspension brackets (centre bracket
22
22
) with reflector location tabs
AR
/AR
HB
fitted. The other end of the reflector is free
floating to allow for thermal expansion.
'U' tube
AR13 UT/AR13 HB
Affix the single reflector to the locating
tabs with M6 nuts, bolts and washers
provided. Fit the reflector end caps using
M5 screws, washers and 'S' clips.
AR22 UT/AR22 HB
Insert the two reflectors into the suspension
with the punched holes exactly in line with
the centre bracket holes. Secure with M6
nuts, bolts and washers provided, passing
through both reflector sections. Fit reflector
end caps using M5 screws, washers and 'S'
clips.
AR35 UT/AR35 HB and AR40 UT/AR40 HB
Position the first reflector section and secure
it to the bracket nearest the burner position
with M6 nuts, bolts and washers provided.
Position the second and third sections so
they overlap with the punched holes in line
with the tabs on the third suspension
bracket from the burner position. The first
reflector must lie on top of the second
reflector. Secure using M6 nuts, bolts and
washers provided, passing through both
reflector sections fit reflector end caps using
M5 screws, washers and 'S' clips.
AR45 UT/AR45 HB and AR50 UT/AR50 HB
Position first and second reflector sections
so they overlap with the punched holes in
line with the tabs on the second suspension
bracket from the burner and secure using
M6 nuts, bolts and washers provided,
passing through both reflector sections.
Position third and fourth reflector sections
so they overlap with punched holes in line
with the tabs on the fourth suspension
bracket and secure using M6 nuts, bolts
and washers provided. Ensure the second
reflector is placed over the third reflector.
Fit reflector end caps using M5 screws,
washers and 'S' clips.
Linear
AR13 SL/HB
Position both reflectors into the brackets
so they overlap with the holes coinciding
with the locating tabs on the Type 'A' second
bracket. Secure using M6 bolts, nuts and
large washers passing through both
reflector sections and tabs. Fit reflector end
caps using M5 screws, washers and 'S' clips.
AR22 SL/HB
Position the first reflector section and secure
it with the M6 bolts, nuts and large washers
to the Type 'A' suspension bracket nearest
the burner. Position the second and third
sections of the reflector so that they overlap
with the punched holes in line with the lugs
provided on the third suspension bracket
from the burner. Secure using M6 bolts, nuts
and large washers passing through both
reflector sections. Fit reflector end caps
using M5 screws, washers and 'S' clips.
Ensure the second reflector is placed over
the third reflector.
AR35 and 40 SL/HB
Position the first reflector section and secure
it with the M6 bolts, nuts and large washers
to the Type 'A' suspension bracket nearest
the burner. Position the second reflector so
they overlap with the punched holes in line
with the tabs provided on the third
suspension bracket from the burner. Position
the fourth reflector in the fourth bracket,
and attach the reflector to the fifth bracket.
Secure using M6 bolts, nuts and large
washers passing through both reflector
sections where appropriate. Fit reflector end
caps using M5 screws, washers and 'S' clips.
Ensure the second reflector is placed over
the third reflector.
AR45 and 50 SL/HB
Position the first reflector section and secure
it with the M6 bolts, nuts and large washers
to the Type 'A' suspension bracket nearest
the burner. Position the second and third
section of reflector so that they overlap
with the punched holes in line with the
tabs provided on this suspension bracket
from the burner. Where required, fit fifth
and sixth reflector sections to sixth and
seventh brackets. Secure using M6 bolts,
nuts and large washers passing through
both reflector sections where appropriate.
Fit reflector end caps using M5 screws,
washers and 'S' clips. Ensure the second
reflector is placed over the third reflector.
Note The above assembly instructions apply
to ARE SL/HB series of heaters. However, end
caps are not supplied.
7