Ambu aView JANUS2-W08-R10 Manual de instruções de utilização - Página 5

Procurar online ou descarregar pdf Manual de instruções de utilização para Monitor Ambu aView JANUS2-W08-R10. Ambu aView JANUS2-W08-R10 17 páginas.

Imprimir página

4. Use of aView

Numbers in gray circles below refer to illustrations on page 2.

4.1. Preparation and Inspection of aView

Closely examine aView and all parts for any damage (free from wear and tear) 1 .

Place aView on a solid flat surface by using the stand on the back of aView 2a .

If needed, aView can be placed on a pole by using the supplied bracket 2b .

Switch aView on by pressing the power button

aView is loading the User Interface will appear on the screen.

Check the battery indicator on aView. A full charge lasts approximately 3 hours. Charge

the aView monitor if necessary by connecting the aView power supply to the wall socket

and insert the power plug into the power inlet of aView 4 . Make sure the power supply

is present and working at any time. It is recommended to locate the nearest wall socket

before start of the procedure.

The battery icon remains white until one block is left, after which it turns red.

When remaining battery capacity is 10% the red battery icon starts flashing.

Max. battery

Min. battery

status of

the aView

Charging is shown with blocks flashing. Current capacity is shown with non-flashing blocks.

Battery is

Battery current

charging

capacity

The power button will light up green when aView is turned ON and not connected to mains

and orange when aView is connected to mains. When aView is turned off, fully charged and

connected to mains the button will turn green.

If the battery is critically low, the recording functions will become unavailable.

If the aView is turned off and the battery is critically low, the power button will flash orange

five times every ten seconds to remind that charging is needed.

Connect the selected Ambu visualization device to aView by plugging the cable connector

into the corresponding female connector on aView (push aside the rubber cover)

5a or 5b . Align the arrows on the visualisation device and aView before insertion.

Verify that a live video image appears on the screen. Point the distal end of the Ambu

visualization device towards an object, e.g. the palm of your hand 6 .

Adjust the image preferences on aView if necessary – please refer to the online extended

aView Instruction for Use on www.ambu.com for details.

Medical — general medical equipment as to

electrical shock, fire and mechanical hazards

only in accordance with

ANSI/AAMI ES60601-1:2005/(R):2012

CAN/CSA-C22.2 No. 60601-1:08 (R2013)

IEC 60601-2-18:2009. UL60601-1, 1st ed.: 2006

CAN/CSA-C22.2 No. 601.1-M90, 2005

IEC 60601-2-18:1996. Control no 4UD1.

INMETRO Certificate Medical Electrical

Equipment

ABNT NBR IEC 60601-1,

ABNT NBR IEC 60601-1-2,

ABNT NBR IEC 60601-2-18.

3 . A white hourglass indicating that

Fully charged

battery still connected

to charger

Battery damaged

4.2. Installing, Preparing and Operating the Ambu Visualization Device

Please refer to the Instruction for Use for the specific visualization device.

4.3. Operating the aView Monitor

Startup Image Mode

Starts immediately after the power

button is pressed and continues

until the User Interface is loaded

(after approximately 1 min).

A live image from the plugged in Ambu

visualization device is available while aView

is loading. If no device is connected the

screen will be blue.

The screen layout may vary depending on

the software version.

Interface nomenclature

Power button

Brightness adjustment

Contrast adjustment

Snap shot

Live image vs. recorded image

Round BLUE buttons are shown in the blue Live Image tab

Square YELLOW or GREEN buttons are shown in the yellow File Management tab

green Settings tab

and indicates a recorded image.

Battery status: During start up, aView powers up and configures the visualization device.

If the aView battery icon on the screen changes from fully charged to low battery (red battery)

within 30 minutes, aView must be replaced.

Connection to external monitor

The image from an Ambu visualization device can be viewed on an external monitor using the

video out interface on aView. Connect the external monitor to the composite interface on the

right side of aView using the adaptor cable supplied (refer to the online aView User Guide on

www.ambu.com). Please consult the manual of the external monitor for further information on

how to connect an external video source by composite.

User Interface

A live image is available and the User

Interface displays advanced user functions

(refer to the online aView User Guide on

www.ambu.com).

aView starts up in the Blue tab for Live Image

Viewing and recording live image.

The screen layout may vary depending on

the software version.

Video recording

Viewing and recording

live image.

Managing saved files.

System settings and User

Accounts.

and indicates a live image.

and the