Coaguchek XS Plus System Começar a trabalhar - Página 2

Procurar online ou descarregar pdf Começar a trabalhar para Equipamento médico Coaguchek XS Plus System. Coaguchek XS Plus System 2 páginas.

Imprimir página

preparIng tO run an OptIOnal lIquID qualItY COntrOl test

1. gather the Following Items

• CoaguChek XS Plus Meter

• Container of test strips

• Test Strip Code Chip

• CoaguChek XS Pro PT Control

Solutions

• Diluent Dropper (2)

• Quality Control Code Chip

runnIng an OptIOnal lIquID qualItY COntrOl test

1. remove a test strip

Take a test strip out of the container.

Close the container tightly.

You have 10 minutes to use a test strip

once you remove it from the container.

6. Collect Control

Using the dropper, gently squeeze

Apply a drop of control to the target area.

and hold the bulb. Insert the tip of the

Hold the control drop to the test strip until

dropper into the control solution. Slowly

you hear a beep. The flashing dropper

release the bulb to draw the control up

symbol will disappear. An hourglass will

to the bulb. Avoid creating bubbles in

appear, indicating the test is in progress.

the control.

Return any unused control to the bottle

for additional tests. Reconstituted controls

are good for 30 minutes.

The result appears in less than one

minute.

2. Match Code

The code number on the control

solution and the Quality Control Code

Chip must match.

Each box of controls comes with a

matching code chip. Control code

chips are identified with a "C" in

the number.

2. Insert test strip

Slide the test strip into the test strip

guide in the direction of the arrows

until it stops.

The meter powers on, and the main

menu appears.

7. apply the Control

Record your result as instructed by

your facility.

Note: If during testing the meter displays

an error message, refer to the Error

Messages section of the Operator's

Manual for an explanation and steps on

how to proceed.

Run a level 2 control test with a new test

strip following the same steps.

3. reconstitute Control solution

Open a bottle of lyophilized control.

Cut off the flared tip of the dropper at

the end of the stem.

Hold the diluent dropper vertically by

the stem, not the bulb, to avoid loss of

diluent.

Do not hold the pipette close to

your face.

3. select Control test

Press Control test on the main menu

screen.

An hourglass symbol appears.

The QC Test menu appears.

8. record result

Remove the Quality Control Code Chip

and store it with the remaining controls.

Replace the Test Strip Code Chip.

Roche Diagnostics recommends that you

keep a code chip in the slot to keep the

electrical contacts free of dirt.

Transfer the entire contents of the

Close the bottle.

dropper to the bottle. Do not touch the

Gently swirl the bottle using a circular

dropper to the dried material or to the

motion to dissolve the dried material.

sides of the bottle.

Do not shake or turn the bottle on its

Do not discard the dropper. You will

side or upside down. Avoid creating

need it to apply a drop of control to

bubbles.

the test strip later in the test.

Let the bottle sit undisturbed for at

least a minute to ensure that the dry

material dissolves completely.

4. Insert qC Code Chip

5. select the level

Press new on the QC Test menu.

Select level 1 for running a level one

control.

A code chip symbol with a flashing

arrow appears on the screen.

An hourglass symbol appears.

Remove the Test Strip Code Chip and

A test strip symbol appears with a

insert the Quality Control Code Chip

flashing dropper symbol. You have

with the number facing up until it

180 seconds to apply the quality

snaps into place.

control solution.

The meter stores the code chip

information in memory for future use.

9. remove Control Code Chip

10. Clean up

Place the used strip and control bottles

in an approved biohazard container.

Power the meter off.

Refer to cleaning and disinfecting

procedures in the Operator' s Manual.

ACCU-CHEK, COAGUCHEK and SAFE-T-PRO

are trademarks of Roche.

Roche Diagnostics GmbH

Sandhofer Strasse 116

68305 Mannheim, Germany

Made in Germany

Manufactured for and distributed in the USA by:

Roche Diagnostics

9115 Hague Road

Indianapolis, IN 46250-0457

Rx Only