Coast to Coast WF2AU1B Manual de operação - Página 9

Procurar online ou descarregar pdf Manual de operação para Extensor Coast to Coast WF2AU1B. Coast to Coast WF2AU1B 16 páginas. Long-range, high-performance cellular wifi extender

Imprimir página
WINEGARD
CONNECT
®

Troubleshooting

LED DEFINITION (LOCATED UNDER THE SIM CARD / LED COVER) :
LED OFF
SOLID RED
FAST BLINKING GREEN
FAST BLINKING ORANGE
SOLID GREEN
ALTERNATING GREEN/ORANGE
QUESTION
Am I able to paint the Winegard ConnecT
2.0?
I am not seeing the SSID (NETWORK
NAME) for my ConnecT system.
The system software shows I'm connected
to a WiFi source but why aren't the web
pages loading?
After updating the software and logging
into the system, the CONNECT ANTENNA
status field on the main Status screen
shows "Installing Software" for an
indefinite period.
What if I lost my manual and/or cannot
find my SSID or password?
What do I do if 10.11.12.1 does not bring
up the login screen?
My device shows the SSID but when I
enter the correct password it will not
connect.
After switching from WiFi to 4G or vice
versa my Internet Status field will not
connect.
What is the No Internet button on the
main screen used for?
What happens if my firmware update
failed?
2.0 SUPPORT
™
System is powered down.
System is booting up.
System is initializing.
System is up and waiting for an Internet connection.
System is connected to the Internet.
System is being updated with new software
ANSWER
Do not paint any portion of the ConnecT system. Painting the system could impact the performance
and possibly cause damage, which would void the warranty.
Check that the LED, located under the SIM Card/LED cover entry plate, is powered on. If not, with
a voltage meter, verify that 12V is getting from the vehicle power to the dome. If it is powered on
and you do not see the SSID, reset the unit by pressing and holding the reset button under the
SIM Card/LED cover plate for 30 seconds.
Some WiFi sources do not require a password to connect but do require something before they will
let you use their network. In these cases, they will often have a "SPLASH" page that requires you
to either agree to their rules or enter a password before they will allow you to use their network.
These pages will not always load on the web browser that you select but instead open on your
devices default browser. Sometimes browsing to a web page will also bring up this splash page.
Return to the Update Software screen and click on the RESTORE button. This will complete the
update on the Winegard ConnecT system.
If you haven't changed your factory preset SSID or password you have some options to recover these:
1. Located on the side of the dome is a SIM card /LED cover plate. Inside this plate there will
be a white label with your factory preset SSID and password.
If you have changed your password you have 2 options:
1. Inside the SIM Card/LED cover plate there is a reset button on the left hand side. Press and
hold the reset button for 30 seconds. This will restore the unit to the original factory settings.
Then you may log in using the factory SSID and password located on the front of this manual or
inside the cover plate.
2. If you are unable to gain access to the outside antenna you can also do a power cycle to get
the unit back to the factory defaults. (See the Reset/Return to Factory Defaults section of this
manual on page 5).
One of several things has happened. The first thing to check is the WiFi signal that your device is
connected to. If this is not the Winegard ConnecT SSID, this address isn't valid. If you are indeed
connected to the correct network, the address may have been changed. To resolve this, perform a
factory reset. See the Reset/Return to Factory Defaults section of this manual on page 5.
Try resetting the ConnecT 2.0 to see if your device will then connect. See the Reset/Return to
Factory Defaults section of this manual on page 6.
Verify that your device is still connected to the ConnecT. When switching between 4G and WiFi
your device may have stopped the connection. In order to avoid this, it is recommended to have
your device set to auto connect to the ConnecT when in proximity.
The No Internet button allows the user to turn off auto connect if there is no WiFi around. When
auto connect feature searches for nearby saved WiFi networks, the local AP turns off causing the
user's device(s) to disconnect and reconnect continuously.
First connect to a WiFi source. Navigate to the Update Software drop-down and click select.
Finally click on the Recover Modem button. This will reconfigure your modem.
8