AeroBed 109 AU Manual de instruções - Página 4
Procurar online ou descarregar pdf Manual de instruções para Bomba de água AeroBed 109 AU. AeroBed 109 AU 4 páginas.
Imprimir páginaDEFLATION AND STORAGE
1. Open the Quick Air Release Valve cover at the
head of the bed to release the air.
2. Fold sides of bed into the center along its
length. Tightly roll your bed towards the
Quick Air Release Valve at the end of the bed.
3. Roll the bed completely until all air is
expelled. When the bed is completely rolled,
push the Quick Air Release Valve closed and
locked for its next use.
4. Slide the duffel bag over your bed. Store your
bed and pump until its next use.
CARE AND MAINTENANCE
1. Inspect your bed prior to each use.
2. Keep your bed away from any sharp objects or obstacles with
rough edges. Large cuts or snags may not be repairable and will
not be covered by your bed warranty.
3. When not in use, store your AeroBed
clean, dry place out of extreme temperatures. Note: Bed must be
at room temperature prior to inflating or it may cause air leaks.
4. In case of incidental damage to your bed, repair patches have
been included. Please follow repair instructions carefully.
CLEANING
We recommend that you do not let the plush surface on top of
your bed get wet. Repeated exposure to water or other liquids may
cause damage to the plush surface that will not be covered by your
warranty. Should liquid come in contact with the plush surface, blot
liquid dry and use a damp cloth to remove any stain. Let surface air
dry completely.
You may clean the PVC on the sides and bottom of your bed with
a mild dishwashing detergent or household cleaner. Do not use
chemicals or other compounds. Avoid the use of scouring pads,
harsh detergents, solvents, polish, abrasive or aerosol cleaners as
they may damage the bed. Allow your bed to air dry completely after
cleaning and before storing.
CAUTION: To reduce the risk of electric shock, do not immerse or
expose the Adaptor/Charger, Pump Motor or Flexible Cord to water,
rain or any other liquid, or charge the Pump near baths, basins, or
other vessels containing water or other liquids, or when standing in
or on damp or wet surfaces. The Pump should never be immersed
or exposed to rain, moisture or any liquid. If any Electrical product
falls into water, or if water should accidentally enter the Pump Motor
or Adaptor/Charger, UNPLUG it immediately; DO NOT REACH INTO
THE WATER.
Important: Prior to reconnecting to the Power Supply, the complete
Product should be inspected by a qualified technician.
Sport bed and pump in a
®
TROUBLESHOOTING
Very rarely, your AeroBed
Sport bed may fail to inflate properly.
®
Should this occur, please use the following check list.
1. If your bed doesn't appear to be inflating:
Check to see that your pump is fully charged.
Make sure the Air Release Valve is closed.
If the valve is open, close it by using 2
thumbs to push cover firmly into valve. Be
careful to avoid pushing valve cover to the
right or left as it snaps into valve opening.
2. If air leakage from the Air Release
Valve occurs:
Carefully remove the round soft gasket
around the inside of the Air Release
Valve cover.
Rinse the gasket in warm water for 10
minutes, then towel dry.
Re-insert in the valve cover, making
certain that the side of the gasket with
the U-shaped groove faces into the
cover. Leave valve in open position for
approximately 30 minutes. Then close and proceed with
inflating instructions.
3. If trouble persists, contact our Customer Service Centre, 9.00 am
to 4.00 pm EST weekdays on Freecall 1800 224 350
for assistance.
Or visit our website at: www.aerobed.com.au
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice.