American Standard 2476 Instruções de instalação Cuidados e manutenção - Página 2
Procurar online ou descarregar pdf Instruções de instalação Cuidados e manutenção para Casas de banho American Standard 2476. American Standard 2476 13 páginas. Dual flush 2-piece toilet
Também para American Standard 2476: Instruções de instalação (4 páginas)
Imprimir página
6
BOLT CAP
CLOSET BOLT
WASHER
NUT
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
!
DO NOT OVERTIGHTEN NUTS
b. Install caps on washers.
c. Smooth off the bead of sealant around base.
Remove excess sealant.
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
9a
Before continuing, determine the type of water supply connection you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL / COPPER
METAL FLANGED
FLARED TUBING
TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not
apply to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
WARNING: Do not use plumber's putty, pipe dope, or any other sealant on the water supply connection to
!
this tank. If the connection leaks after hand tightening, replace the supply line. If the connection continues
to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.
CLOSET FLANGE
CAUTION:
METAL SPIRAL
TUBING
LOCK NUT
LOCK NUT
EXISTING
EXISTING
WASHER
CONE
WASHER
EXISTING
COUPLING
COUPLING
NUT
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Use existing
Use existing spiral
coupling nut
cone washer.
and washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
7
Tank Installation Kit Includes:
2 bolts, 2 rubber washers, 4 metal washers, 4 metal nuts,
2 plastic nuts, 1 large rubber gasket.
TANK MTG.
WASHER
NUT
WASHER
INSTALL TANK
a. Discard plastic nuts.
b. Install tank mounting bolts and rubber washers from inside
tank, through mounting holes and secure with one metal
washer and one nut per bolt.
c. Install large rubber gasket over threaded outlet on bottom of
tank and lower tank onto bowl so that tapered end of gasket
fits evenly into bowl water inlet opening.
d. With tank parallel to wall, secure tank to bowl using remaining
two metal washers and nuts. Alternately tighten nuts until
tank is snugged down evenly against bowl surface.
*
USE NUT DRIVER OR DEEP SOCKET RACHET.
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
9b
VINYL / BRAIDED
CONNECTOR
LOCK NUT
COUPLING
NUT
WATER
SHUT-OFF
Captive cone
washers already
included. No
additional washers
needed.
- 2 -
RUBBER
WASHER
RUBBER
GASKET
BOLTS
NUT
!
CAUTION:
With correct washers in
place (see Step 9a),
tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
7301144 -1 0 0 Re v. G