eKey multi CP DRM 4 Manual de início rápido

Procurar online ou descarregar pdf Manual de início rápido para Porta de entrada eKey multi CP DRM 4. eKey multi CP DRM 4 2 páginas.

Imprimir página

QUICK-START GUIDE

ekey multi CP DRM 4

Networked

access

system

without

PC,

with

fingerprint scanning

ID17/174/0/83:

Version 2 dated

5.12.2012

CONTACT

Should you have any technical questions, please contact an ekey

reseller!

NOTE ON THE DOCUMENT

This quick-start guide as well as the additional information and instructions on the

supplied DVD are not subject to updating. You can find the most up-to-date version of

these documents on www.ekey.net. Subject to optical and technical modifications, any

liability for misprints excluded.

WARNING !

In addition to these instructions, also observe the information on the DVD

supplied together with the product.

START-UP

Please follow the steps below to start up the system:

1.) Make everything you need ready to mount the devices as

described in the mounting instructions supplied with the devices.

2.) Wiring

Do not connect the system to the mains yet! The electrical

connection of the system can only be carried out by a

specialist!

Connect the wires as described in the ekey home wiring plan

supplied with the devices.

3.) Check the wiring.

4.) Conclude mounting the devices. Close all the device housings

which you had to open in order to be able to proceed with the

wiring.

5.) Read carefully the following chapter

„Operating the finger scanner". The correct operation

(i.e. swiping the finger over the sensor) of the

fingerprint

scanner

decisive

for

the

functioning of the whole system.

6.) Connect the power adaptor to the mains.

The electrical connection of the system can only be

carried out by a specialist

The ekey multi CP DRM 4 displays the language selection

The ekey home finger scanner indicators are as follows:

ekey home FS OM

ekey home FS IN

ekey home FS WM

flashing

orange

7.) Now start at point 1: INITIALIZING THE DEVICES of

„Programming the system".

2 Operating the finger scanner

2.1.Function of the finger scanner

The function of the finger scanner is to capture and analyze the image of your finger, and then

compare it with a reference template. Which part of your finger should be captured?

It is necessary to capture an image of the 3rd

Finger nail

phalanx. On the contrary, your finger scanner

Finger

image

will not function properly.

(papillary

3rd phalanx

In order to ensure this, take care to operate the

(phalanx distalis)

lines)

of the

finger scanner correctly. It is fundamental to

3rd

phalanx

place your finger correctly in the finger recess

Fingergliedes)

and move it down across the sensor at the right

speed. Ergonomically speaking, the best fingers

2nd phalanx

are the index, the middle finger and the ring

(phalanx media)

finger. The

not

A finger scanner works like a camera. It makes a picture of the bottom side, the papillary lines, of

your finger´s third phalanx. However, this picture must be of good quality, so that physical access

can be granted whenever necessary.

Imagine you wish to make a picture of someone, and this person

keeps fidgetting

runs by and you try to make a picture of him at that exact moment

hides half of his face behind a tree

etc.

What do you think these pictures will look like? On some of the pictures you will not even be able

to recognize the person.

The finger scanner works in the same way. The finger scanner can only read all the information

contained in your finger, and consequently open your doors securely and reliably, if you move

your finger down across the sensor evenly and in the right position.

Let us now look at where you should place your fingers and at which speed you should move them

across the sensor, so that the „pictures" of your fingers are perfect.

2.2 The finger recess – the control element

The finger recess allows to place the finger correctly so that a finger picture of good quality

can be captured. It actually is the control element and consists of

Pin point

Sensor

- right and left recess edges

3. Programming the ekey multi CP DRM 4 system

proper

3.1.Function of the control panel

The ekey multi CP DRM 4 in the ekey multi system is meant to

program and parametrize the system.

Using the

LCD display and the

4 buttons,

you can

Delete users

Enter the security code

Change the security code

Set time zones

Change the relay switching times

Retrieve LOG data

Reset to factory settings

The menu navigation is intuitive and very easy. You will find

step-by-step detailed

explanations

of each specific menu

function on page 2.

2.3. Operating correctly the finger scannner

thumb

and the

little finger

may

be used!

Ideally, when positioning your

finger on the finger recess, stretch

the remaining fingers, holding them

close to the „swiping" finger. This

helps keep the „swiping" finger

2.4. What you should not do

Left and right recess

edge

Place your third phalanx

higher than the pin point

PIN POINT

SENSOR

3.2.Controls and their symbols

Lay your finger straight and flat

on the finger recess.

PLACE the middle

BE SURE to place

of your third

your finger exactly

phalanx directly

in the middle of

on the finger

the area between

recess

point.

both finger recess

Now without changing the inclination of your finger, move it down across

the sensor (the entire hand). Take care to swipe your finger at the right

speed. BEWARE: The entire movement (swipe) should take about

Use this as a benchmark. You should not need much more or much less

than that. If you swipe your finger too fast, then the status LED shows

„red"

Do not modify the position of the finger phalanges during

the swipe (e.g. by bending the third phalanx).

There is no need to exert any

your finger across the sensor as if you would wipe bread

crumbs off a table.

even.

Not place your finger in the middle

Rotate your finger in the

of the finger recess, or not place it

parallel to the finger recess edges.

speed

If you move your finger across the finger scanner in one of the

ways mentioned here, then the scanner will not be able to

Move

your

extract the information it needs about your finger image. It

finger too fast

will therefore not function properly:

or too slowly

Poor recognition performance: You will have to swipe your

across

the

finger several times across the sensor before being able to

sensor.

induce the door to open.

Reference templates cannot be saved: You are not able to

save a finger in the system, because the finger scanner gets less

information.

3.3. Programming the system

Now start programming the system. The menu

The LCD display guides you through the menu,

sequences

allows you to read status messages and to set

explained below. Let us not forget to mention

given features.

the security code. You need it in order to be able

to make changes in the system. The factory

default setting for this code is 99. Change

this code to another one of your choice as

The OK button allows you to register

soon as you have started up the system.

values and move to the next menu level.

The Down arrow and the Right arrow

buttons allow you to set values and to

navigate in the menu.

The Up arrow and the Left arrow

buttons allow you to set values and to

navigate in the menu.

The ESC button

allows you to exit

a menu level or to cancel entries.

Take care to position your

finger as flat as possible

over the finger recess.

There should be only a

small slit left between

edges.

sensor and finger.

1-1,5 sec

pressure. Move

stronger

Place your finger at a too

finger recess.

steep angle with the

finger recess.

for

each

single

function

are

Security code

Factory setting