American Standard 3636 NEO Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Acessórios American Standard 3636 NEO. American Standard 3636 NEO 2 páginas. Acrylic shower base

Imprimir página

American Standard 3636 NEO Instruções de instalação

Insure the floor and stud walls are square and plumb. Provide a 5" x 5" (127mm x

127mm) opening in the floor for the drain (see Figs. A & B). The drain plug

accom-modates a 2" (51mm) PVC waste pipe. The waste pipe should extend above

the surface of the sub-floor, refer to chart on page 2 for the required dimensions.

See product drawings on this page for the specified drain locations.

3636.NEO, 3838.NEO, 4242.NEO

C/L

90°

6-5/8

51 mm (2)

127mmx127mm

PVC Waste Pipe

(5x5) Opening

(See Product Chart for Drain Location)

Note: Variations in

levelness of the subfloor

may require adjustment

of waste pipe height.

* For 6032.STRH and

6032.STLH, see drawing

for proper location of

5" x 5" drain cut-out.

Before installing drain into

the shower base, remove

strainer (see Fig. C). This

will be installed after

shower base is in its final

position. Install the drain to

the shower base as shown

in Fig. D. Use silicone

sealant between drain

body and shower base.

No Bedding

Bedding Material Area

Under

Apron

159mm

(6-5/8)

Bedding

Material

127 mm (5)

Draw a line 6-5/8" (159mm) from the

sub-floor on to the studs at each

side of the opening. Using this line

and a level, mark the remaining

studs. (See Figs. A & B.) This will be

the installed height of the shower

base. Mix the low-shrink bedding

material (grout, mortar, plaster, etc.).

Concrete is not recommended.

Apply enough bedding material to

support the entire bottom of the

shower base. The bedding material

must not be used under the apron

(front edge).

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

A S A m e r i c a , I n c . 2 0 0 8

3232.ST, 3636.ST, 4242ST, 6034.ST, 4834.ST, 4832.ST

90°

6-5/8

90°

51 mm (2)

PVC Waste Pipe

(See Product Chart for Drain Location)

SHOWER BASE

WASTE PIPE HEIGHT

3636.NEO

3838.NEO

4242.NEO

3232.ST

4834.ST

6034.ST

3636.ST

4242.ST

4832.ST

6032.STRH/LH*

DRAIN

ASSEMBLY

Rubber

Caulking

Gasket

Drain

Body

Silicone

Sealant

Rubber

Gasket

Waterproof

Drywall

13mm (1/2")

minimum

51 mm (2)

PVC Pipe

51x102 mm

(2x4) Stud Wall

Lift and lower base over center

of drain pipe and set into place

90°

127mmx127mm

C/L

(5x5) Opening

5/16" ± 1/16"

3/8" ± 1/16"

5/16" ± 1/16"

3/8" ± 1/16"

1/4" ± 1/16"

5/16" ± 1/16"

1/2" ± 1/16"

Strainer

Shower

Base

Fiber

Gasket

Locking

Nut

3 mm

(1/8)

CLEANING AND MAINTENANCE

Your American Standard shower base is designed to last indefinitely

with reasonable care and maintenance.

The high-gloss acrylic surface is resistant to impact and retains its luster

with proper care and maintenance. An integral, slip-resistant surface is

incorporated for user safety.

General Cleaning: Do not use abrasive cleaners; a mixture of warm

water and a mild liquid detergent is adequate for most cleaning. Strong

detergents formulated for use on tile or porcelain-enamel surfaces

should be avoided.

Caution: Do not allow liquid detergent containers to remain on base

surfaces for more than a few moments. Do not use Lestoil, Windex, Mr.

Clean, Dow Disinfectant (spray or concentrate), or Lysol Basin, Tub and

Tile Cleaner. Do not allow nail polish remover, dry cleaning fluid, acetone,

paint remover, or other solvents to contact acrylic surface.

After the bedding material has been poured and

before it sets, lower the shower base into position

with the drain assembly sliding over the waste pipe

as shown in Fig. E. It will be necessary to "rock" the

shower base until the top of the tile flange aligns

with the lines drawn in Step 3 on the stud walls.

Make certain the apron is contacting the rough floor

along the entire length of the shower base. Insure

that the base is level in two directions (see Fig. F).

Snap strainer back into place and check for proper

drainage.

Level

Level base in two directions.

Secure the base to the studs as shown, using the

screws and the brackets provided. See Fig. G.

Note: Allow the bedding material to completely

harden before applying weight to the bottom of

the shower base.

Base Flange

Drywall

Screw

Shower

Base

Tape over the strainer to protect the finish

and prevent construction debris from

entering the drain.

Finish installation as shown in Figure H.

Caulk

Shower

Base

Level

Bracket

Stud

Tile

Waterproof

Drywall

Tile

Adhesive

Bracket

Stud

Splash

Lip

Flange

751817-100 Rev. Q