American Time SiteSync IQ Manual de instalação de início rápido - Página 2

Procurar online ou descarregar pdf Manual de instalação de início rápido para Relógio American Time SiteSync IQ. American Time SiteSync IQ 2 páginas. Wireless clock system gps plus with ethernet & campus tx antenna
Também para American Time SiteSync IQ: Manual de instalação de início rápido (2 páginas), Manual de instalação e operação (2 páginas), Manual de instalação e operação (13 páginas), Manual de instalação e operação (7 páginas), Manual de instalação e operação (6 páginas), Manual de instalação de início rápido (2 páginas), Manual de instalação de início rápido (2 páginas), Manual de instalação de início rápido (2 páginas), Manual de instalação de início rápido (2 páginas), Manual de instalação de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas)

Imprimir página
American Time SiteSync IQ Manual de instalação de início rápido
QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• GPS receiver with 15' cable and mounting bracket
• Power supply
(B)
• Magnetic mount TX antenna with 12' cable
• Installation and Operation Manual
3
Choose your location
• Choose a location for the GPS receiver outside, mounted
parallel to the horizon, with a clear view of the sky and the
label facing up. The included mounting bracket allows for
mounting on the side of a building or other structure.
Avoid high voltage equipment and excessive roof overhang
when choosing a location.
• Choose a location for your magnetic mount TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller and must always point up or down,
never horizontal! The cable length cannot be extended.
System controller
located high & central
4
Connect cables to the system controller
A.
Connect the GPS antenna to the STD GPS RJ45 port.
B.
Connect the system controller power supply to the POWER
INPUT port.
C.
Connect the magnet mount TX antenna to the TX ANT port.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
Note: If your system controller supports more than one time sync
option, refer to the SiteSync IQ Installation & Operation Manual for
(A)
detailed instructions.
(C)
C
GPS signal in
4 ft
minimum
TX Ant signal
out to clocks
SITESYNC IQ
A
B
To local
power
(110vac)
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
GPS=Y
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
2. Create a 4 digit User Lock or enter 0000 to disable this
O
feature. Press
.
Tip: Record this password.
3. Create a 4 digit Service Lock (for advanced features) or enter
O
0000 to disable this feature. Press
Tip: Record this password.
4. Select local time zone by using the
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from.
8
5. Press
to select automatic DST (Daylight Saving Time) or
0
to disable DST if your location doesn't observe DST.
Press
O
6. Press
1
for 12-hour mode - AM/PM (1:00PM).
Press
2
for 24-hour mode - Military (13:00).
7. To confirm proper set up, press
8
• If successful, "GPS Sync Successful" will display
• If not successful, "GPS Sync Failed" will display. Re-try
by pressing
8
again.
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON
MAR
10
2014
10:38:06 AM
USCT
American Time
Status=AUTO
MON MAR 14 2016
10:38:06 AM USCT
American Timel
Status=AUTO
(Page 9 in Installation Manual)
.
<>
keys. Press
O
.
Note: Screen
will advance
immediately
to sync.
TX
GPS=Y