Door-Gard COMMAND AND CONTROL SERIES Manual de programação - Página 3
Procurar online ou descarregar pdf Manual de programação para Teclado Door-Gard COMMAND AND CONTROL SERIES. Door-Gard COMMAND AND CONTROL SERIES 4 páginas.
Imprimir página
3
PROGRAMMING OPTIONS CHART
If the pre-programmed default values must be changed
or additional functions are desired, the following options may be programmed.
1. Enter programming mode
2. Change master code/set main relay time
Example: Master code of 4321/relay time of 10 seconds
3. Add/change user code
4. Add/change user code with a different output
time on main relay
1 (SEE BELOW)
5. Delete user codes
1 (SEE BELOW)
6. Set output 2 time
7. Set output 3 time
1 (SEE BELOW)
8. Set output 4 time
1 (SEE BELOW)
9. Set outputs for Remote Triggering Input
10. Set outputs for Panic
11. Turn keypress feedback/audible keypress on
12. Turn keypress feedback/audible keypress off
13. Turn yellow LED/sounder on with relay
14. Turn yellow LED/sounder off with relay
15. Turn auto entry on
16. Turn auto entry off
17. Turn keypad active output on
18. Turn keypad active off
19. Erase keypad memory/reset defaults
20. Energize selected output(s) with a user code
Example: User 2; code of 4321*; energize outputs 2 & 3
NOTES:
1 1
Relay time must always be represented by 2 digits. Example: 5 seconds = 05.
Latching /toggle is accomplished by entering a time of 00
2 2
If selected, panic will operate by pressing the * and # simultaneously.
Panic operates for 1 second and is defaulted to output 4.
3 3
Keypad active is a negative voltage output (sink) available
on terminal (or wire) marked WB (see wiring diagrams for location).
4 4
This feature is not available with the master code.
1 (SEE BELOW)
2 (SEE BELOW)
3 (SEE BELOW)
4
Press
99 # (master code)
Press
( Relay Time ) # 1 # (new code) * (repeat code) *
Press
10 # 1 # 4321 * 4321 *
Press
(user location) # (new code) * (repeat code) *
Press
(Relay Time) # (user location) # (new code) *
(repeat code) *
Press
(user location) # * *
Press
12 # (Relay Time) # 0 # * *
Press
13 # (Relay Time ) # 0 # * *
Press
14 # (Relay Time ) # 0 # * *
Press
17 # (outputs: .ie. 1, 2 or 2, 3 etc.) # 0 # * *
Note: 0= no outputs
Press
18 # (outputs: i.e. 1, 2 or 2, 3 etc.) # 0 # * *
Note 0= no outputs
Press
30 # 0 # 1 # * *
Press
30 # 0 # 0 # * *
Press
30 # 1 # 1 # * *
Press
30 # 1 # 0 # * *
Press
30 # 2 # 1 # * *
Press
30 # 2 # 0 # * *
Press
43 # 0 # 99 # * *
Press
43 # 0 # 00 # * *
Press
46 # 00000 # 00000 # * *
Press
59 # (outputs: i.e. 1, 2 or 2, 3 etc.) #
(user location) # (new code) * (repeat code) *
Press
59 # 23 # 02# 4321 * 4321 *
* *