Astria Polaris42ZEP Manual de instruções de instalação - Página 15

Procurar online ou descarregar pdf Manual de instruções de instalação para Lareira exterior Astria Polaris42ZEP. Astria Polaris42ZEP 16 páginas. Outdoor decorative gas fireplace

Imprimir página

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in

accordance with the manufacturer's instructions and all applicable codes

and requirements of the authority having jurisdiction. If the information in

these instruction is not followed exactly, a fire, explosion or production of

carbon monoxide may result causing property damage, personal injury

or loss of life. The qualified service agency is responsible for the proper

installation of this kit. The installation is not proper and complete until the

operation of the converted appliance is checked as specified in the manu-

facturer's instructions supplied with the kit.The qualified service agency

performing this installation assumes responsibility for this conversion.

Cette trousse de conversion doit être installée par un technicien agréé,

selon les instructions du fabricant et selon toutes les exigences et tous les

codes pertinents de l'autorité compétente. Assurez-vous de bien suivre

les instructions dans cette notice pour réduire au minimum le risque

d'incendie, d'explosion ou la production de monoxyde de carbone pouvant

causer des dommages matériels, des blessures ou la mort. Le tecnicien

agréé est responsable de l'installation de cette trousse. L'installation n'est

pas adéquate ni complète tant que le bon fonctionnement de l'appareil

converti n'a pas été vérifié selon les instructions du fabricant fournies avec

la trousse. Le fournisseur de service qualifié ayant réalisé l'installation

assume les responsabilités liées à la conversion.

In Canada:

THE CONVERSION SHALL BE CARRIED OUT

IN ACCORDANCE WITH THE REQUIREMENTS

OF THE PROVINCIAL AUTHORITIES HAVING

JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN/CGA-B149.1

AND .2 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE

CONFORMÉMENT AUX RECOMMANDATIONS

DES AUTORITÉS PROVINCIALES AYANT

JURIDICTION ET CONFORMÉMENT AUX

EXIGENCES DU CODE D'INSTALLATION CAN/

CGA-B149.1 ET.2.

Gas conversion kits are available to adapt your

appliance from the use of one type of gas to

the use of another. These kits contain all the

necessary components needed to complete the

task including labeling that must be affixed to

ensure safe operation.

Kit part numbers are listed here and the fol-

lowing steps detail the conversion procedure.

WARNING

AVERTISSEMENT

Step 1. Turn off the gas supply to the appliance.

Step 2. Carefully remove the logs. Exercise

care so as not to break the logs.

Step 3. Refer to Figure 19.

Remove the burner assembly with attached

venturi tube.

Natural to Propane Gas Conversion Kits

Model No.

Polaris36

GCK-DB078P

Polaris42

GCK-DB078P

Propane to Natural Gas Conversion Kits

Model No.

Polaris36

GCK-DB140N

Polaris42

GCK-DB140N

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Unit Type

Cat. No.

H4916

Unit Type

Cat. No.

H4915

Remove Tube

Remove Clip

Shutter

Opening

Orifice

Regulator

Figure 19

Electronic Appliances

Step 4. Dexen Electronic Valves - See Figure

20 and the instructions provided with the kit.

Remove and discard the two pressure regulator

mounting screws. Remove the pressure regula-

tor and diaphragm. Discard all removed compo-

nents. Ensure the rubber gasket installed on the

back of the replacement pressure regulator is

properly positioned. Install the new pressure

regulator using the new screws supplied with

the kit. Tighten screws to 25 In. lb. torque.

NOTE: Natural gas regulators are identified with

a blue dot. Propane regulators have a red dot.

Step 5. See Figure 21 and replace the pilot

orifice as follows: Remove pilot hood assembly

by grasping the hood and pulling the assembly

straight up. Under the hood is the pilot orifice.

With caution and using a magnetic screwdriver,

undo the pilot orifice and remove it from the

assembly. Carefully replace the orifice with the

one provided with the kit. Press the pilot hood

back over the assembly. The orientation should

be aligned as shown in Figure 21. Exercise

extreme care to prevent damage to or break-

age of the igniter assembly.

NOTE: Propane pilot orifices are identified with

a countersink in the head. Natural gas orifices

do not have this countersink. See Figure 21.