Astro Pneumatic Tool 1833 Manual

Procurar online ou descarregar pdf Manual para Chave de impacto Astro Pneumatic Tool 1833. Astro Pneumatic Tool 1833 4 páginas. 3/8" nano flex-head angle impact wrench - 400ft/lb

Imprimir página

Model:

1833

WARNING

Study, understand and follow all instructions provided

with this product. Read these instructions carefully

before installing, operating, servicing or repairing this

tool. Keep these instructions in a safe accessible place.

INTENDED USE OF THE TOOL

The 1833 Flex-Head Impact Wrench is designed to be

used for removing and fastening bolts and nuts with

3/8" drive impact sockets only. Do not use this tool

outside of the designed intent. Never modify the tool for

any other purpose or use.

WARNING

Caution: To help prevent personal injury

• Use of this product can expose you to chemicals

such as phthalates which are known to the State of

California to cause cancer, and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov/product.

Always wear ANSI approved safety equipment, safety

glasses and clothing when using this product. Study,

understand, and follow all instructions provided with

this product. Failure to read and follow all warnings

and operating instructions may result in damages

and serious injury or death.

• Always wear ANSI approved goggles when using this

product. (Users and By standers).

• Never use this tool for any application other than for

which it was designed.

• Only use accessories designed for this tool.

• Never alter or modify this tool in any way.

• Improper operation and/or maintenance of the tool,

modification of the tool, or use of the tool with

accessories not designed for it could result in

serious injury or death.

• Always select the correct accessories of the correct

size and design for the job that you are attempting to

perform.

• Always work in a clean, safe, well-lit, organized and

adequately equipped area.

• Do not begin repairs without assurance that vehicle

is in secure position, and will not move during repair.

BEFORE USE

When unpacking, check the parts diagram and part

number listing on page 4 to make sure all parts are

included. If any parts are missing or damaged,

please call your distributor.

DO NOT DISCARD – GIVE TO USER

Product Type:

3/8" NANO FLEX-HEAD ANGLE

IMPACT WRENCH - 400FT/LB

1 YEAR LIMITED WARRANTY

• Astro Pneumatic Tool Co. warrants our products to the

original user against defective material or workmanship

for a period of 1 year (except where noted on our price

schedule) from the date of 1st use. Astro reserves the

right to determine whether the product failed because of

defective material, workmanship or other causes and to

charge back for missing parts. Astro Pneumatic Tool

Co., at its discretion, will repair products covered under

this warranty free of charge. The distributor should

direct the original user to return the product (with the

exceptions listed below) with the distributor's name,

address, adequate proof of date of purchase or a copy

of warranty card, and a short note explaining the

problem. Failures caused by accident, alteration, or

misuse are not covered by this warranty.

• Astro Pneumatic Tool Co. or its authorized service

representatives must perform all warranty repairs. Any

repair to the product by unauthorized service represen-

tatives voids this warranty. The rights under this warran-

ty are limited to the original user and may not be

transferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed

or implied, including warranties of merchantability and

fitness for a particular purpose. Some states do not

allow the exclusion of limitations of incidental or conse-

quential damages so the above limitations may not

apply to you.

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

1-800-221-9705 FOR INSTRUCTIONS

PRODUCT INFORMATION

• An industry first true flex-head impact wrench and

with our shortest length yet at 3.34"

• Patented design features innovative dual air intake

motor and twin hammer mechanism for increased

power, and 180° flex-head with 360° swivel handle

for maximum access

• Perfect for brake caliper bolts or wherever you can

hook the ultra-slim impact head

Specification:

Square Drive: 3/8"

Working Torque: 280ft.lbs

Max Torque: 400ft.lbs

Overall Length: 3.34"(85mm)

Vibration Level: 4.9m/sec

Air Inlet: 1/4"(6.35mm)

Free Speed: 8000 R.P.M

Page 1

www.astrotools.com

Air Pressure: 90 psi

Recommended Minimum

Hose Bore Diameter: 3/8"(10mm)

Recommended Maximum

Hose Length: 30 ft (10m)

Clutch Type: Twin Hammer

Av. Air Consumption: 4 CFM