Flying Industry Development 0020686 Manual do utilizador - Página 2

Procurar online ou descarregar pdf Manual do utilizador para Recetor Flying Industry Development 0020686. Flying Industry Development 0020686 3 páginas. 5000 meters rf wireless receiver

Imprimir página
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Terminals "NO" and "COM" are Normally Open;
Terminals "NC" and "COM" are Normally Closed.
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal "L / +", and connect the negative pole of DC power supply to terminal "N / -".
2) Connect terminal "NO" to the positive pole of DC power supply, connect terminal "COM" to the positive pole of DC lamp, and connect the negative
pole of DC lamp to the negative pole of DC power supply.
If you want to control an AC 220V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal "L / +", and connect the negative pole of DC power supply to terminal "N / -".
2) Connect terminal "NO" to the live wire of AC power supply, connect terminal "COM" to one side of AC lamp, and connect another side of AC lamp
to the neutral wire of AC power supply.
Setting different control modes：
We have set the receiver in toggle mode before delivery, if you want to use other modes, do as following operation.
1) Setting control mode Toggle: Turn on the first bit of the dip switch.
Control mode Toggle (with transmitter CC-2): Press -> On; Press again -> Off.
Press the first button of the transmitter: Turn on the relay1 (connect terminals "NO1" and "COM1", disconnect terminals "NC1" and "COM1"), the lamp
1 is turned on.
Press the first button of the transmitter again: Turn off the relay1 (disconnect terminals "NO1" and "COM1", connect terminals "NC1" and "COM1"),
the lamp 1 is turned off.
Press the second button of the transmitter: Turn on the relay 2 (connect terminals "NO2" and "COM2", disconnect terminals "NC2" and "COM2"), the
lamp 2 is turned on.
Press the second button of the transmitter again: Turn off the relay 2 (disconnect terminals "NO2" and "COM2", connect terminals "NC2" and
"COM2"), the lamp 2 is turned off.
2) Setting control mode Momentary: Turn on the first and the second bits of the dip switch.
Control mode Momentary (with transmitter CC-2): Press and hold -> On; Release -> Off.
Press and hold the first button of the transmitter: Turn on the relay1 (connect terminals "NO1" and "COM1", disconnect terminals "NC1" and "COM1"),
the lamp 1 is turned on.
Release the first button: Turn off the relay1 (disconnect terminals "NO1" and "COM1", connect terminals "NC1" and "COM1"), the lamp 1 is turned off.
Press and hold the second button of the transmitter: Turn on the relay 2 (connect terminals "NO2" and "COM2", disconnect terminals "NC2" and
"COM2"), the lamp 2 is turned on.
Release the second button: Turn off the relay 2 (disconnect terminals "NO2" and "COM2", connect terminals "NC2" and "COM2"), the lamp 2 is
turned off.
3) Setting control mode Latched: Turn on the second bit of the dip switch.
Control mode Latched (with transmitter CC-4): Press button A -> On; Press button B -> Off.
Press button A of the transmitter: Turn on the relay 1, the lamp 1 is turned on. And turn off the relay 2 at the same time, the lamp 2 is turned off.
Press button B of the transmitter: Turn on the relay 2, the lamp 2 is turned on. And turn off the relay 1 at the same time, the lamp 1 is turned off.
Press button C/D of the transmitter: Turn off two relays 1 and 2, two lamps 1 and 2 are turned off.
Wired control terminals:
The receiver has wired control terminals, you can connect external devices, sensors, limit switches or manual switches to trigger the receiver.
1) By low level signal:
You can connect external devices (with low level output signal) to trigger the receiver.
When external device outputs low level signal to terminals 1 and 3, turn on the relay 1, and the lamp 1 is turned on.
When external device stops to output signal, turn off the relay 1, and the lamp 1 is turned off.
When external device outputs low level signal to terminals 2 and 3, turn on the relay 2, and the lamp 2 is turned on.
When external device stops to output signal, turn off the relay 2, and the lamp 2 is turned off.
2) By NO/NC contact:
You can connect manual switches (with NO/NC contact) to trigger the receiver.
When connect terminals 1 and 3 by manual switch, turn on the relay 1, and the lamp 1 is turned on.
When disconnect terminals 1 and 3 by manual switch, turn off the relay 1, and the lamp 1 is turned off.
When connect terminals 2 and 3 by manual switch, turn on the relay 2, and the lamp 2 is turned on.
When disconnect terminals 2 and 3 by manual switch, turn off the relay 2, and the lamp 2 is turned off.
Setting feedback function:
If you want to switch on feedback function: You need to turn on the third bit of the dip switch.
When the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter. When the transmitter receive the feedback
signal of the receiver, the transmitter will exude a buzzing sound like "D~" which means it receive the feedback signal successfully.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is turned on. The receiver starts the LEARNING procedure.
SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com