Ametek SurgeX SX2210 Instruções de instalação - Página 3
Procurar online ou descarregar pdf Instruções de instalação para Controlador Ametek SurgeX SX2210. Ametek SurgeX SX2210 5 páginas.
Imprimir página
SX2200 Series
Installation Instructions:
Caution:
®
SurgeX
2200 series products permit a maximum 16A
(SX2216 models), 15A (SX2215 models), 13A (SX2213
models) or 10A (SX2210 models) total output load,
each outlet is capable of providing the maximum load
individually. Make sure that the total does not exceed the
current limit of your mains receptacle.
For safety please plug your SurgeX
receptacle (T20AL 250V fuse recommended).
®
®
SurgeX
Series Mode
the polarity indicator is illuminated when connected to the
mains please replace the plug observing correct polarity.
Mounting
®
The SurgeX
SX2200 series are designed to be installed in
a 19 inch equipment rack and require two units (2-U) of rack
space. Remove the product from its packaging and slide it into
place in the rack, being careful to feed the power cord into the
rack first. Guide the power cord and plug so that they do not
get caught or jammed as the product is installed.
240 Volt Connections
Connect power to the unit by plugging the cord into a 240V
mains receptacle. The SX2200 series must be plugged into
the appropriate properly polarized receptacle.
Model
Standard Total Load
SX2210
AS3112
10A
SX2213
BS1363
13A
SX2215
BS546
15A
SX2216
CEE7/7
16A
The SX2200 series have a total of six rear AC outlets: five
switched and one always on. The SX2200 series also feature
a front panel courtesy outlet, which is always on (excluding RL
models). Plug the equipment into the always-on and switched
AC outlets as needed to power the equipment.
© 2019 AMETEK Electronic Systems Protection
®
unit into a fused
Protection is Live-Neutral only, if
Receptacle
Australian style receptacle
British style receptacle
South African / Indian style
receptacle
European style receptacle
The always-on and courtesy receptacles (where fitted) provide
power as long as it is supplied to the SurgeX
switched rear receptacles provide power only when the front
panel switch is on and, in the case of RT products, when the
remote control input is also activated.
Indicator Lights
The SX2200 series have two, three or four indicator lights on
the front panel depending on the model. All models feature a
polarity indicator lamp on the rear panel:
Amber polarity light (Rear panel, all products): When
illuminated indicates that live and neutral are reversed and
your SurgeX product will not work as intended. If you are using
an SX2216 (European CEE7/7 connectivity) simply reverse
the connection. If you are using an SX2210, SX2213 or
SX2215 consult an electrician to correctly wire your receptacle
and establish proper polarity.
Red Power Light (All products): indicates that power is
supplied to the unit and the power switch is turned on.
Green Self-Test Light (All products): indicates that power is
supplied to the unit and the internal surge protection circuitry
is fully functional.
Orange Over/Under Voltage Protection Light (RT & RL
products): indicates that the mains voltage is below 190 volts
or above 280 volts.
Yellow Remote Light (RT products): indicates that the
remote control is active and the rear switched receptacles are
on. (The power switch must also be on).
Task Lamp Connectors (RL Only)
The RL version has provision for two task lamps. Plug the
lamps into the two three-pin XLR connectors on the front panel
and use the dimmer to set a suitable brightness. Standard or
HI brightness lamps can be used. Each connector can supply
up to 5 Watts maximum. LED type lamps can be used with the
RL but the dimmer must be set fully clockwise.
UM-SX2200-Rev-B
®
. The five
surgex.com