Double K Industries CHALLEGAIR LARGE ANIMAL DRYER BLOWER Instruções e precauções de segurança - Página 2

Procurar online ou descarregar pdf Instruções e precauções de segurança para Produtos para animais de estimação Double K Industries CHALLEGAIR LARGE ANIMAL DRYER BLOWER. Double K Industries CHALLEGAIR LARGE ANIMAL DRYER BLOWER 4 páginas.

Imprimir página

IMPORTANT SAFEGUARDS

WARNING: IMPORTANT SAFETY PRECAUTIONS! PLEASE READ
COMPLETELY BEFORE USING PRODUCT!
When using electrical appliances, especially in the presence of children and animals, basic
safety precautions should always be followed to reduce the risk of re, electric shock, and
personal injury, including but not limited to the following:
DO NOT TURN ON DRYER WITHOUT FIRST HOLDING THE DRYER HOSE, as the air volume from
the dryer can cause the hose to whip or move rapidly and may cause injury.
1.
Do not leave dryer OR the animal unattended while product is in use.
2.
Unplug unit when not in use.
3.
Do not use extension cords with dryer.
4.
Do not unplug unit by pulling on cord.
5.
Do not expose dryer to rain or water.
6.
Do not use or store dryer where it can fall or be pulled into tub or sink or standing water.
If dryer falls into water . . . UNPLUG IT . . . Do not reach into the water!
7.
Unplug unit before attempting any maintenance or service.
8.
Do not put any object into dryer openings.
9.
Keep loose clothing, jewelry and hair away from dryer openings.
10.
Do not direct dryer air towards eyes or ears of people or pets.
11.
Never use dryer if it has a damaged cord or plug, has been dropped, damaged or
exposed to rain or water. Return to Double K Industries or an Authorized Service
Center for service.
12.
This dryer should not be used as a cage dryer, for cage drying please consider our model
560 Cage dryer.
13.
This product is for use on animals only.
14.
Recommended operation by adults only. Use caution when working around children.
15.
Do not use attachments not recommended by Double K Industries.
16.
Do not operate without lters in place. Keep lters clean, as dirty lters limit air intake
and may damage the motor or cause overheating.
17.
Plug only into a properly grounded receptacle. Always make sure the amperage of the
electrical outlet is su cient for the amperage rating of the product. (See Product Speci -
cations for amperage rating of this product).
18.
Do not use product for anything other than its intended purpose.
19.
Do not attempt to perform any service or maintenance not outlined in instruction
manual.
20.
Do not attempt any product modi cations or alterations. Do not use, if any parts or
switches are damaged. Send to an Authorized Service Center or Double K Industries
for service.
21.
When servicing, use only Double K Industries parts.
WARNING: DISCONNECT POWER SUPPLY BEFORE SERVICING
AVERTISSMENT: COUPER L'ALIMENTATION AVANT
L'ENTRETIEN ET LE DÉPANNAGE
2
BRUSHES
Your CHALLENGAIR
LARGE ANIMAL DRYER BLOWER
The brushes should be checked for wear after approximately 500 hours of use. If the
carbon brushes are worn shorter than 1/4 inch, the brushes should be replaced.
Brushes may be ordered from Double K Industries or an Authorized Service Center
(you will need 2 sets, 1 set for each motor). Please be sure to specify that your dryer is
an Extreme™, as the brushes are slightly di erent from one dryer model to another.
To check and/or replace brushes:
1.
Unplug electrical cord from wall outlet.
Disassembly:
2.
Slide o the back cover from the dryer. This is a compression t and will come
o with a little e ort.
3.
Remove all screws on the outside of the dryer that hold the two halves of dryer
housing in place. Lay the dryer on its side while removing these screws. Remove
the O-ring on the snout of the dryer and lift the top half.
4.
Each motor will be sitting in place inside the rubber silicone motor mounts.
Removing the rubber silicone motor mounts from the motor is not neces-
sary to replace brushes. The internal lter frame ts into slots on the inside
of the dryer housing. This piece can remain while changing brushes.
5.
Disconnect motor power wires (see wiring diagram). Note where wires connect.
6.
Motor: (a) Find the ag connector on the top of the brush assembly. There is a
wire leading to this connector. (b) Place a athead screwdriver with a ne tip
between the ag connector and the plastic brush housing. (c) Rock the screw-
driver back and forth and gently wedge the ag connector out of the brush
assembly. (d) Loosen the two brush assembly retainer bracket screws.
(e) Remove the brush assembly. (f)Replace the brush assembly with the new
one, making sure that the small tab on the bottom is tted onto the corre-
sponding slot on the motor frame. (g) Replace the brush assembly retainer
bracket and tighten the screws which hold it in place. (h) Attach the ag
connector to the new brush in the same position as the previous brush.
(i) Repeat these steps for the brush on the other side of the motor.
Reassembly:
7.
Inspect the motor mount for cracks or damage -- replace if necessary.
Set the motor back into its original position in the dryer housing. The
motor mount has slots that t over corresponding alignment tabs on the
inside of the dryer housing. These slots and tabs must match up for proper
t and function. (Note: In the event that the motor mount is removed from
the motor, simply replace it by being mindful to align the contours of the
motor mount with corresponding contours on the motor housing.) Make
sure that the internal lter housing is in its appropriate slot before putting
the halves together.
8.
Reattach the screws around the outside of the dryer making sure the two
halves are matching up.
9.
After the two halves of the dryer housing have been put together, replace
internal lter and push the back cover onto the rear of the dryer. Always make
sure all lters are in place before operating dryer. Replace o-ring on snout.
™ has two brush-type motors.
7