Dover Hydro 39721 Manual de início rápido - Página 2
Procurar online ou descarregar pdf Manual de início rápido para Dispensador Dover Hydro 39721. Dover Hydro 39721 2 páginas. Proportioner with e-gap eductors
Imprimir página
Metering Tip Selection:
The fi nal concentration of the dispensed solution is re-
lated to both the size of the metering tip opening and
the viscosity of the liquid being siphoned. For water-thin
products, the chart at left can be used as a guideline. If
product is noticeably thicker than water, consult the Mea-
surement of Concentration Procedure below to achieve
your desired water-to-product ratio. Because dilution can
vary with water temperature and pressure, actual dilution
achieved can only be ascertained by using the Measure-
ment of Concentration Procedure. The clear, undrilled tip
is provided to permit drilling to size not listed should you
need a dilution ratio that falls between standard tip sizes.
NOTE: A 1 GPM eductor is grey; a 4 GPM eductor is yellow.
Refer to parts diagram if unfamiliar with names of system
components.
Measurement of Concentration:
You can determine the dispensed water-to-product
ratio for any metering tip size and product viscosity.
All that is required is to operate the primed dispenser
for a minute or so and note two things: the amount of
dispensed solution, and the amount of concentrate used
in preparation of the solution dispensed.
Dilution Ratio (X:1) where X = Amount of Mixed Solution — Amount of Concentrate Drawn
Dilution Ratio, then, equals X parts water to one part concentrate (X:1). If the test does not yield the desired ratio, choose a diff erent tip
and repeat the test. Alternative methods to this test are 1) pH (using litmus paper), and 2) titration. Contact your concentrate supplier
for further information on these alternative methods and the materials required to perform them.
AccuPro Select Parts Diagram List:
5
6
APPROXIMATE DILUTIONS
AT 40 PSI FOR WATER-THIN PRODUCTS (1.0 CP)
Tip
Orifi ce
Std. Drill
Ratio (per Eductor Flow)
Color
Size
Number
1 GPM
3.5 GPM
No Tip
.187
(3/16)
2.6:1
Grey
.128
(30)
2.6:1
Black
.098
(40)
2.5:1
Beige
.070
(50)
3:1
Red
.052
(55)
5:1
White
.043
(57)
7:1
Blue
.040
(60)
9:1
Tan
.035
(65)
11:1
Green
.028
(70)
17:1
Orange
.025
(72)
19:1
Brown
.023
(74)
22:1
Yellow
.020
(76)
32:1
Aqua
.018
(77)
39:1
Purple
.014
(79)
64:1
Pink
.010
(87)
128:1
Amount of Concentrate Drawn
4
3
2
1
8
Key
Part No.
Description
1
238100
Strainer washer
7
2
10082830 Swivel collar (molded)
3
10082801 Swivel stem (molded)
4
10075926 Pipe plug
5
10091035 Wall bracket
6
10093995 Cabinet
7
10020700 Selector valve grommet
10020900 Back up ring for grommet
8
10093710 Button, dark grey
9
10075980 Valve parts kit
a. diaphragm, b. armature,
c. spring, d. valve bonnet
10
10079010 Spring
11
10079000 Magnet
12
10075986 Water valve
13a 290
1 GPM eductor assembly
b 291
3.5 GPM eductor assembly
AccuPro Select Parts Diagram:
4:1
4:1
5:1
12
8:1
13:1
22:1
26:1
34:1
13a,b
52:1
64:1
e
71:1
102:1
128:1
213:1
447:1
14a,b
15
9
10
11
16
f
g
h
17
Key
Part No.
Description
14 a 10088822 1 GPM discharge tube assembly
b 90048495 3.5 GPM discharge tube assembly
15
10080730 Hose hook, grey, for
3.5 GPM discharge tube
16
10080957 Selector replacement kit:
e. support clip, f. Suction stub,
g. O-ring, h. selector valve assembly
17
690014
Metering tip (kit)
18
500814
Tubing, 1/4" x 7'
19
10089401 Check valve, in-line, viton
20
10086721 Fitting, Y, 1/4" barb
21
509900
Weight
22
10089410 Footvalve, viton (EPDM also
available order 10076302)
NOT SHOWN:
641751
Screws (cabinet sides)
Pick-up Parts Diagram:
18
19
20
18
20
18
21
22