Dover Hydro AccuDose Series Manual de início rápido - Página 2
Procurar online ou descarregar pdf Manual de início rápido para Dispensador Dover Hydro AccuDose Series. Dover Hydro AccuDose Series 2 páginas. Proportioner with e-gap eductors
Também para Dover Hydro AccuDose Series: Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas)
Imprimir página
Metering Tip Selection:
The final concentration of the dispensed solution is
related to both the size of the metering tip opening
and the viscosity of the liquid being siphoned. For
water-thin products, the chart at left can be used as
a guideline. If product is noticeably thicker than
water, consult the Measurement of Concentration
Procedure below to achieve your desired water-to-
product ratio. Because dilution can vary with water
temperature and pressure, actual dilution achieved
can only be ascertained by using the Measurement
of Concentration Procedure. The clear, undrilled tip
is provided to permit drilling to size not listed should
you need a dilution ratio that falls between standard
tip sizes.
NOTE: A 1 GPM eductor is grey; a 4 GPM eductor
is yellow. Refer to parts diagram if unfamiliar with
names of system components.
Measurement of Concentration:
You can determine the dispensed water-to-product
ratio for any metering tip size and product viscosity.
All that is required is to operate the primed dispenser
for a minute or so and note two things: the amount
of dispensed solution, and the amount of concen-
trate used in preparation of the solution dispensed.
Dilution Ratio (X:1) where X = Amount of Mixed Solution — Amount of Concentrate Drawn
Dilution Ratio, then, equals X parts water to one part concentrate (X:1). If
choose a different tip and repeat the test. Alternative methods to this test are 1) pH (using litmus paper), and 2)
titration. Contact your concentrate supplier for further information on these alternative methods and the materials
required to perform them.
AccuDose Select Parts Diagram List:
5
4
7
APPROXIMATE DILUTIONS
AT 40 PSI FOR WATER-THIN PRODUCTS (1.0 CP)
Ratio (per Eductor Flow)
Orifice
Std. Drill
Tip Color
Size
Number)
1 GPM
3.5 GPM
No Tip
.187
(3/16)
3:1
6.5:1
Grey
.128
(30)
3:1
6.5:1
Black
.098
(40)
3:1
Beige
.070
(50)
4:1
10:1
R e d
.052
(55)
5:1
16:1
White
.043
(57)
7:1
20:1
Blue
.040
(60)
8:1
24:1
Tan
.035
(65)
10:1
30:1
Green
.028
(70)
16:1
45:1
Orange
.025
(72)
20:1
56:1
Brown
.023
(74)
24:1
64:1
Yellow
.020
(76)
32:1
90:1
Aqua
.018
(77)
38:1
128:1
Purple
.014
(79)
64:1
180:1
Pink
.010
(87)
128:1
350:1
Amount of Concentrate Drawn
the test does not yield the desired ratio,
2
1
3
Key
Part No.
Description
1
238100
Strainer washer
2
10082830 Swivel collar (molded)
3
10082801 Swivel stem (molded)
4
10075911 Hex nipple
10075950 O-ring (two per nipple)
6
5
10075925 Pipe plug
6
1 0 0 8 0 7 1 0 Button, grey (standard)
1 0 0 8 0 7 1 1 Button, sky blue
1 0 0 8 0 7 1 2 Button, red
1 0 0 8 0 7 1 3 Button, green
1 0 0 8 0 7 1 4 Button, light grey
8
1 0 0 8 0 7 1 5 Button, yellow
7
1 0 0 8 0 8 9 5 Cabinet
8
10020700 Selector valve grommet
10020900 Back up ring for grommet
9
10075980 Valve parts kit
a. diaphragm, b. armature,
c. spring, d. valve bonnet
AccuDose Select Parts Diagram:
7:1
12a
12b
d
1 3
Key
Part No.
10
10079010 Spring
11
10079000 Magnet
12a 290
b 291
13 a 10088822 1 GPM discharge tube assembly
b 90048495 3.5 GPM discharge tube assembly
1 4
10080730 Hose hook, grey, for
1 5
10080957 Selector replacement kit:
1 6
690014
1 7
500814
1 8
500821
1 9
509900
2 0
10089410 Footvalve, viton (EPDM also
NOT SHOWN:
64 1751
9
1 0
a
b
c
d
1 6
1 5
e
f
g
Description
1 GPM eductor assembly
3.5 GPM eductor assembly
3.5 GPM discharge tube
d. support clip, e. Suction stub,
f. O-ring, g. selector valve assembly
Metering tip (kit)
Tubing, 1/4" x 14'
Tubing, 1/4" x 21'
Weight
available order 10076302)
Screws (cabinet sides)
1 1
4 GPM Eductor (right side)
12b
1 2 c
1 6
1 8
1 3
1 9
2 0
1 4