AMPHIBICO HD Wave WAVH0760 Manual de instruções - Página 9
Procurar online ou descarregar pdf Manual de instruções para Acessórios para câmaras AMPHIBICO HD Wave WAVH0760. AMPHIBICO HD Wave WAVH0760 10 páginas. Amphibico wave housing (for the sony hdr-cx/pj 710, 730, 740 & 760 camcorders)
Imprimir páginaOf the Latches:
The three latches of the Amphibico Pro Digital are designed to have a locking action to prevent accidental opening. Always ensure that the
locking mechanism is secure. Watch for the build-up of corrosion or salt residue around the latches. This will appear as a white material.
Lubricate the latches with a small amount of WD-40 to remove the corrosion or salt residue build-up.
Of the O-Rings:
The O-rings that need to be maintained on a regular basis are the main housing O-ring and the O-ring on the lens port The main O-ring
should be cleaned on a daily basis and the port O-ring should be cleaned daily or each time the port is changed.
Of the sacrificial anode:
The anode attached to the bottom part of the housing is there to prevent corrosion due to electrolysis, as time
goes it will deteriorate and needs to be replacement, contact your dealer for replacement (parts # 19220).
TO SERVICE O-RINGS ON THE HOUSING MAIN O-RING, LENS PORTS.
1. Remove the O-ring. It is important never to use a sharp instrument when removing an O-ring as this may damage
the O-ring groove or the O-ring itself. A bobby pin or edge of a credit card works well.
2. Once the O-ring is removed, it should be examined for damage. Check to make sure that the O-ring is free of nicks and cuts and that it
retains its original round profile. O-rings that appear to be damaged should be discarded immediately and replaced with new O-rings.
3. Rinse the O-ring with fresh water and dry it with a clean lint free cloth.
4. Clean the O-ring groove (where the O-ring sits) with a Q-tip. Be sure to remove any lint the Q-tip may leave
behind. Inspect the groove for damage.
5. Wipe the part of the housing that the O-ring seals against with a clean lint-free cloth.
6. Re-grease the O-ring with a thin layer of O-ring grease until it appears to be smooth and shiny. Do not over grease it. Use just enough
grease so the O-ring will pull smoothly through your fingers. Excessive amounts of
grease will only serve to attract dirt to the o-ring.
7. Make sure that the O-ring is properly (evenly) installed in the O-ring groove.
8. To reinstall the clean and lubricated O-ring, place the entire O-ring over the groove and start by pushing the O-ring in at each corner
then, push the O-ring at each side and finally, work in the rest of the O-ring. Never start at one
end and work your way around the O-ring. This places uneven tension on the O-ring which may cause the O-ring to stretch resulting in
excess O-ring, which will have no place to go.
There are internal O-rings on the housing controls as well. These O-rings are not as susceptible to damage as they are not exposed but
they do require yearly maintenance and are not user serviceable. The housing should be returned to Amphibico or to an authorized Am-
phibico service facility for this annual maintenance. Check for the closest service cen-ter on our website www.amphibico.com
An internal moisture alarm is installed in your Amphibico HD Wave housing (Product # 20023). This moisture alarm is powered by an eas-
ily replaced CR 2032 battery. Please read the instruction sheet provided for your moisture alarm prior to installing the battery.
RECOMMENDED AMPHIBICO ACCESSORIES
MAINTENANCE & REBUILT O-RING KITS
Please visit our website at www.aquatica.ca for a complete selection of our Technical Lighting Control line of strobe arms and supports.
Optional Accessories:
-
WAFP0011 Flat port: $250USD retail
-
OAURPG03 Green Water Filter $85USD retail
-
ORRKT0004 O-Ring Re-built Kit $65USD retail
-
WASH0003 HD WAVE LCD Sun Shade $45USD retail
Page 8