Dover TWG Tulsa 12 Informações sobre peças - Página 2
Procurar online ou descarregar pdf Informações sobre peças para Guinchos Dover TWG Tulsa 12. Dover TWG Tulsa 12 4 páginas.
Imprimir página
Item
Description
1
1
Rod
2
Bracket
1
3
Cotter Pin
1
4
Set Screw
----
5
Washer
----
Cotter Pin
1
6
1
7
Yoke
2
8
Key
9
Washer
1
10
Drum
1
11
"U" Bolt
1
12
Bushing
2
13
Shaft
1
14
Key
2
Nut
2
15
1
16
Gear Carrier
17
Bushing
18
Spacer
----
19
Dowel Pin
----
20
Capscrew
2
21
Lock Washer
2
22
Lock Washer
8
23
Nut
8
24
Poppet
1
1
25
Spring
1
26
Bushing
27
Bracket
1
1
28
Lock Washer
29
Nut
9
*Located on End Backet of Model 12.
tPart of SA3568 Cam Plate
FREQUENCY: Brake adjustment should be checked daily during
heavy use or after one (1) hour of winch operation. Inspection of
brake shoes and drum for wear should be made after every ten (10)
hours of winch operation.
PROCEDURE:
To Adjust Brakes:
1. Remove load from winch cable.
2. Remove sprocket, coupler, universal joint, or motor from input
shaft of winch.
Note: If power source to winch requires no appreciable torque
to turn in a "Neutral" or "Off" position and an adapter
can be made to fit the coupling, this step is not necessary.
3. Using a suitable adapter, place a torque wrench on the input
shaft of the winch (65).
4. Measure torque while turning the input shaft in the payout di
rection. Torque settings should be as follows:
Model
12
Note: The torque value above is necessary to brake the rated
load of the winch. In no case should the brake setting
ever be increased above this torque value.
5. To adjust the brake torque, loosen the two cap screws (40) and
rotate the cam (42). To increase the brake setting, rotate away
from the "0" or center setting. To reduce the brake setting, ro
tate the cam back toward the "0" or center setting.
6. Recheck the torque value as indicated in 4. above.
To Inspect or Repair B rakes:
1. Loosen and remove cap screws (40) and washers (41) from
brake assembly.
12-SLLRO
Part No.
Item
Description
30
Spring
20833
Drag Brake
20830
31
20819
Ass'y
32
Clutch
------------
Frame L.H.
------------
20821
Capscrew
20832
Capscrew
25762
36
Roller
Washer
20728
38
Bracket Ass'y
20708
Capscrew
21129
Capscrew
20710
40
22412
41
Washer
21526
42
Cam
20566
tDrive Screw
22411
tlnstruction
Plate
Cam Plate
------------
Brake Shoe
46
------------
27390
Ass'y
20558
47
Nut
20518
48
Lock Washer
20267
Key
939264
50
Drum
51
Grease
20444
Retainer
939266
52
Capscrew
20841
Housing
20518
Gasket
20267
54
BRAKE ADJUSTMENT
Torque (lb.-ft.)
�
Item
Part No.
Qty.
1
20299
56
1
SA 1413
1
58
20712
1
20835
60
8
20310
1
20842
61
1
30564
62
2
23591
63
2
SA3343
64
4
28578
65
2
170177
66
2
20617
1
67
23875
68
3
------------
69
1
70
------------
1
SA3568
71
2
SA1733
72
73
1
20114
1
20115
75
1
20279
76
1
29503
78
2
20232
79
12 939261
80
1
23872
81
2
20731
2. Gently pry the cam (42) out of the cover (45).
Caution: Be sure to note which set of drilled and tapped holes
were used to position the cam. Failure to re-install the
cam in this position will result in the brake engaging in
the inhaul rather than the payout mode.
3. Remove the cap screws (39) from the cover (45).
4. Remove the cover (45) from the brake housing (53).
5. The brake shoes (46) may now be removed for inspection.
6. If the shoe linings are worn flush with the rivet heads, they
should be replaced.
7. Inspect the drum (50) for severe wear or scoring. If necessary,
replace the drum.
8. To remove the brake drum, remove the nut (47) and washer (48).
9. Insert two cap screws in the holes provided in the brake drum
and, using a gear puller, remove the drum.
10. Inspect the inside lower part of the brake housing for the pre-
sence of oil. If an oil leak exists, replace the seal (51).
To
Change Direction of Brake Engagement:
1. Remove cap screws (40) and washers (41 ).
2. Rotate cam (42) in either direction until another set of drilled
and tapped holes becomes visible through the slots in the cam.
3. Re-install the cap screws (40) and washers (41) in these tapped
holes.
4. Adjust brake as described above.
Caution: Any change in winch mounting, direction of cable
spooling, or replacement of worm and gear may effect
the operation of the brake. If you have any question
about the performance of the brake on your Tulsa
winch, stop using it immediately and contact Tulsa
Winch, or one of our authorized distributors.
Description
Part No.
Qty.
Bearing
2
20732
Housing
1
20828
Name Plate
1
*21184
Drive Screw
4
21775
Nut
4
20271
Lock Washer
5
20526
Pipe Plug
3
20286
Dowel Pin
2
20517
Lock Washer
21
20526
20271
Nut
20
Worm (L.H.)
1
20809
Worm (R.H.)
1
20808
Cap
1
20815
Washer
1
20092
Capscrew
1
20278
Key
1
20105
Frame, R.H.
1
20836
1
Gear, L.H.
20812
Gear, R.H.
1
20811
Gasket
2
20730
Cover
1
40970
Capscrew
4
20325
Capscrew
4
33469
Grease Fitting
3
21128
1
26799
Breather
20325
Capscrew
12
Roll Pin
1
21527
Lock Washer
4
20526
Nut
4
20271