DPS TL1 MUX-8 Manual de operação - Página 3

Procurar online ou descarregar pdf Manual de operação para Hardware de rede DPS TL1 MUX-8. DPS TL1 MUX-8 8 páginas.

Imprimir página

Type TINSTALL <ENTER>. Follow the directions on the

screen.

Start T/MUX

Select the hard drive and the T/Config directory.

Type T/CONFIG <ENTER>.

Highlight T/MUX <ENTER>.

The first screen will request initials. Enter your initials and

press <ENTER>.

Main Menu

The Main Menu (Fig. 4) lists the functions available in

T/MUX. Each of these Main Menu items is explained in the

following paragraphs.Most fields will have an associated "de-

fault box" that appears. To select from the default box press Tab

and use the Tab key or cursor arrows to highligh the desired

value, then press <ENTER>.

Open MUX

This selection is used to open an existing configuration or to

Fig. 5 - Main Menu Lists the Functions Available in

T/MUX

name a new one. When this function is selected a box will ap-

pear with three fields, as explained in Table A.

Table A - Field Names and Descriptions in the Open

MUX Box

Field Name

Enter a new name or select an existing one from the de-

NAME

fault box. The name will appear in the Title Bar at the

top of the screen at all times. The name should be exclu-

sive to this configuration.

Enter a name that describes the location of the unit.

SITE NAME

(Mandatory field.)

Optional field for additional identifying information,

COMMENT

such as date or initials of preparer.

Edit MUX Configuration

This selection presents the Edit MUX Configuration screen.

See Fig. 6. Set parameters for each of the eight ports and the

MUX (common) Port in this screen. Parameters and their val-

ues are listed in Table B.

D-PC-180-10A-XV

November 5, 1997

Description

Table B - Field Names and Descriptions in the Edit

Configurations Screen

Field Name

Time to delay before aborting an incomplete TL1 mes-

Msg Timeout

sage. Enter in tenths of seconds (10-255). Default is 10.

Off, 300, 1200, 2400 and 9600

Baud

EVEN, NONE, ODD

Parity

7 BITS, 8 BITS

Word Length

1 BIT, 2 BITS

Stop Bits

TTL, RS232, RS422, RS485, 202

Interface

"Hot Keys" available in the Edit MUX Configuration screen

Fig. 6 - Set TL1 Port Parameters in the Edit

Configurations Screen

are shown on the line at the bottom of the screen. See Table C.

Table C - Hot Keys in the Edit Configurations Screen

Key

Select default box.

Tab

Go to previous field.

Up Arrow

Go to previous port.

Go to next port.

Save

Help

Go to first field or exit.

F1-/Esc

Craft Connect

Use this menu item when connecting to the craft port on the

front of the MUX for downloading or other functions. NOTE:

When using this function, the MUX port is not active. A

sub-menu offers the functions listed in Table D:

Table D - Field Names and Descriptions in the Craft

Connect Menu

Field Name

Configure the unit using the selected configuration (re-

DOWNLOAD

fer to the title bar). Starts as soon as <ENTER> is

pressed.

Retrieve configuration from the unit. Overwrites se-

UPLOAD

lected configuration. Starts as soon as <ENTER> is

pressed.

Monitor operational status. (Fig. 7) Screen shows local

MONITOR

alarm and control point status. (Shown in this screen

only.) It also displays four operational status points for

use by DPS Technical Support. Press F7 for the Modem

Tuning window.

Retrieve and display the unit*s configuration status.

INQUIRE

Exit this function and return to the Main Menu.

QUIT

Description

Function

Description

OG1074A7