Bosch SGV68U53UC/C6 Manual de Instruções - Página 22
Procurar online ou descarregar pdf Manual de Instruções para Máquina de lavar loiça Bosch SGV68U53UC/C6. Bosch SGV68U53UC/C6 27 páginas.
Imprimir página
Troubleshooting Guide
Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The
following information may help you with a dishwasher problem without involving a repair professional.
Problem
Cycle does
1. Door is opened longer than 4 seconds after a
not resume
cycle has started.
after door is
opened and
closed
during cycle.
1. Door may not be properly latched.
2. Unit may not be turned on.
3. Unit not reset or previous cycle not com-
pleted.
Dishwasher
4. Delay start engaged.
does not
5. Interruption of electrical power supply to
start
dishwasher or blown fuse.
6. The door may have been closed without first
selecting a cycle.
7. Water supply may not be turned on.
Dishwasher
1. Default factory settings alert the customer
beeping
that the cycle is complete by beeping. This
(end of cycle
feature can be deactivated if so desired.
signal)
2. Water connection is lost.
Display does
1. A fuse may have been blown or circuit
not illumi-
breaker tripped.
nate or con-
2. Door not closed or latched.
sole lights
are not on
Dishwasher
1. Incoming water is not warm enough.
seems to run
2. Cycle time can vary due to soil and water
a long time
conditions.
3. Rinse aid dispenser is empty.
4. Dishwasher connected to cold water supply.
Note: Refer to "Wash Cycle Information" sec-
tion in this manual for typical cycle lengths.
Dishes are
1. Spray arm movement obstructed.
not getting
2. Spray arm nozzles clogged.
clean
3. Improper use of detergents.
enough
4. Filters could be clogged.
5. Dishes are nested or loaded too close
together.
6. Selected wash cycle is not suitable for food
soil conditions.
20
Cause
Action
1. Press [START / RESUME] button and close the
door within 4 seconds to resume cycle.
1. Shut the door completely.
2. Press the main power switch to turn unit on.
3. To reset, refer to "Operating the Dishwasher"
in this manual.
4. To reset, refer to "Delay Start" section in this
manual.
5. Check circuit breaker.
6. Select a cycle and press Start/Resume.
7. Check and turn on water supply.
1. To adjust the volume or deactivate, refer to
the "Cycle Completion Signal" section in this
manual.
2. Check and turn on water supply.
1. Check the fuse or circuit breaker box and
replace the fuse or reset the breaker if neces-
sary.
2. Ensure door is properly latched and com-
pletely closed.
1. Before starting a cycle, run hot water faucet
at the sink closest to the dishwasher.
2. Sensors in the dishwasher automatically
increase the cycle time to ensure a good wash
when heavy soil is detected.
3. Add rinse aid.
4. Verify dishwasher is connected to hot water
supply plumbing.
1. Ensure that spray arm movement is not
blocked by hand rotating spray arms before
starting cycle.
2. Remove the spray arms and clean according
to the "Care and Maintenance" section of the
manual.
3. Increase or decrease detergent depending on
the water hardness (refer to Table 1).
4. Clean the filters according to the "Care and
Maintenance" section of the manual.
5. Rearrange load such that water spray can
reach all items in the dishwasher - see "Load-
ing the Dishwasher" section of the manual.
6. Refer to "Wash Cycle Information" section of
the manual.