Electrolux 63K906 Manual do utilizador - Página 12

Procurar online ou descarregar pdf Manual do utilizador para Forno Electrolux 63K906. Electrolux 63K906 15 páginas. Built - in cooking appliances

Imprimir página

1. Oven Dimensions

installation

WARNING

warning

USE AN AUTHORISED PERSON

As stated in the local municipal building codes and other relevant

statutory regulations.

• W iring connections must be in accordance with AS/NZS

3000 Wiring Rules and any particular conditions of the

local authority.

• R efer to data plate for rating information and circuit diagram.

The data plate is positioned behind the bottom of the oven

door. The circuit diagram is positioned on the top panel of

the appliance.

• A n all pole disconnect functional switch should be provided

near the appliance in an accessible position. Refer to AS/

NZS 3000 clause 4.3.11

• W iring should be protected against mechanical failure.

Refer to AS/NZS 3000 clause 3.9

• A means of disconnection with a contact separation of at least

3mm must be supplied in the fixed wiring.

• T o gain access to the mains connection terminals, remove

the rear panel by unscrewing the 2 assembly screws.

Note: Where connection is made to a multi-phase 240V

supply, the bridge piece should be removed from between

the active connections.

WARNING

warning

IMPORTANT: This appliance must be properly earthed.

• D o not lift the appliance by the door handles.

• P repare the cupboard opening to match your appliance

measurements. (See diagrams).

• S lide appliance into the cupboard, ensuring that the supply

cable (where fitted) does not kink.

• T o prevent tipping, use the screws supplied to secure your

oven into the cupboard. Use just 2 screws for single cavity

ovens and 4 screws for dual cavity. Remove the bottom

door in dual cavity ovens to provide access to the bottom

2 screwing points. (See illustration page 23).

• F or appliances fitted with a supply flexible cord, if the cord

is damaged, it must be replaced by the manufacturer or its

service agent or similarly qualified person in order to avoid

a hazard. The plug must be accessible after installation.

• W here the appliance is built into a cabinet, the cabinet

material must be capable of withstanding 70°C. Installation

into low temperature tolerant cabinetry (e.g. vinyl coated)

22 INSTALLATION Built-in Cooking

may result in deterioration of the low temperature coating by

discolouring or bubbling.

• I f the appliance is installed adjacent to vinyl-wrapped surfaces,

use an installation kit available from the vinyl-wrap supplier.

• E lectrolux Home Products cannot accept responsibility

for damage caused by installation into low temperature

tolerant cabinets.

• A fter installation, test and ensure that the appliance operates

correctly before handing it over to the customer.

warning

WARNING

CAUtIoN: to avoid any potential hazard, you must follow our

instructions below when you install your appliance. Failure to

install the appliance correctly could invalidate any warranty

or liability claims and lead to prosecution.

installation

Cabinet Construction for your appliance

For the best integration within a kitchen, install this appliance in

a standard 600mm wide cupboard that gives a flush fit with the

surrounding cupboard fronts (figure A).

Infill panel

Cleat

20mm

100mm max

20mm

100mm max

Cupboard

door

Figure A – Flush fit (top view)

figure a – flush fit (top view)

oven Dimensions

Underbench Oven

595 x 595 x 567mm (HxWxD)

Separate Grill Underbench Oven

725 x 595 x 567mm (HxWxD)

Separate Grill Wall Oven

888 x 595 x 567mm (HxWxD)

underbench ovens

Your underbench oven looks best when the control panel is directly

under the benchtop. An upper infill panel may have to be added

if the cooktop placed above the benchtop is too deep.

Refer to cooktop installation instructions for required clearance

between cooktop and oven.

A recess of 20 mm is ideal. It can also be installed using a proud

fit with the surrounding cupboard (figure B).

Note: Your appliance must be mounted on a flat surface for

the full width and depth of the product.

Cleat

100mm max

Cupboard front

Figure B – Proud fit (top view)

figure B – Proud fit (top view)

Note: If a powerpoint is fitted it must be

accessible with the appliance installed.

Built-in Cooking INSTALLATION 23

100mm max