DRAKE RMM12 Manual rápido

Procurar online ou descarregar pdf Manual rápido para Racks & Stands DRAKE RMM12. DRAKE RMM12 2 páginas. Rack mount
Também para DRAKE RMM12: Manual rápido (2 páginas)

Imprimir página
The RMM12 Ra ck Mount supports a single Drake Power
Supply and up to (12) modular Audio/Video modulators to
con gure a professional quality, modular, headend system,
which optimizes rack spac e.
Identify the following items shipped with this kit of rack mount
assem bly and ca ble assem bly:
(1) RMM12 Ra ck Mount chassi s.
(1) Wire, ground bonding chassis to power supply
(1) C able Ass embly, 37-pin D connector (mal e) to (12) fan-out
3-Ckt connectors (female)
(2) End Cap s, Bla ck
Ins tallation :
Adequate ventilation is very important in multichan nel
installation s. Ra ck units should be spaced apa rt by at least
one panel height wherever pos sible, and so me air movement
is advis able in enclos ed rack cabi nets. E xces s ive heat will
sho rten the life of components and individual module(s).
Power supply performance will also be degraded without
proper cooling.
BL ACK END CAP
RM M12
(DEC OR ATI VE )
A U DIO
A U DIO
VIDEO
VIDEO
PWR
PWR
A / V
A / V
#
#
#
CH
CH
CH
RF
RF
FIGURE 1 - Front View of Rack Mount System with
R .L. DR A K E HOLDINGS LLC
9900 Springboro Pike
Miamisburg, Ohio 45342
CUSTOMER
SERVICE
AND PARTS TELEPHONE:
FAX: +1 (937) 806-1510
http://www.rldrake.com
®
SECURE
LUG (G R OUND
BONDING WIRE) UNDER
#6- 32 S C R E W HEA D.
A U DIO
A U DIO
A U DIO
A U DIO
VIDEO
VIDEO
VIDEO
VIDEO
PWR
PWR
PWR
PWR
A / V
A / V
A / V
A / V
#
#
#
#
CH
CH
CH
CH
RF
RF
RF
RF
Power Supply
®
+1 (937) 746-6990
RMM12 Rac k Mount
If desired, the supplied black end caps can be installed over
the mounting ears of the RMM12 and secured by the rack
support s crews.
Locate the Power Supply (sold sepa rately) . P rior to sliding the
power supply into the right-ha nd side top and bottom s lide rails
of the RMM12, loosen the #6-32 scr ew located on the top
sur face of the power supply. Position the free end of the
ground wire lug (other end of wire fastened to RMM12) under
the #6-32 scr ew, and tighten the scr ew to secure the ground
wire. Slide the power supply into the RMM12.
If necessa ry, use the following steps to remove the Drake
Power Supply from the rack:
1) Rem ove the module immediately adjacent to the Drake
Power Suppl y. Be aware that the module power ca ble will
become disconnected from the rear when the module is
removed.
2) Now grasp the edge of the Drake Power Supply front panel
and remove the unit from rack.
3) R econnect the module power cable then replace the
adjacent module as required.
SLIDE RAIL (INTERNAL
TO R ACK CHASSI S , TOP
AND B OT TOM).
A U DIO
A U DIO
A U DIO
A U DIO
VIDEO
VIDEO
VIDEO
VIDEO
PWR
PWR
PWR
PWR
A / V
A / V
A / V
A / V
#
#
#
#
CH
CH
CH
CH
RF
RF
RF
RF
® is a registered trade mark of the R . L. Drake Holdings LLC
© Copyri ght 2013
A U DIO
A U DIO
VIDEO
VIDEO
PWR
PWR
A / V
A / V
#
CH
RF
RF
R . L
.
Drake Holdings LLC
Printed in Taiwan.
1
BL ACK END CAP
(DEC OR ATIVE)
P OW E R S U P P LY
P/N: 651231900A