Draper 101059 Instruções de instalação

Procurar online ou descarregar pdf Instruções de instalação para Ecrã de projeção Draper 101059. Draper 101059 2 páginas. Electric projection screen

Imprimir página

Premier Electric Projection Screen by Draper

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation con trary to instructions in val i dates warranty.

➂ Screen should be accessible for complete removal should fabric become damaged

or should other ser vice be required.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) packed separately in screen carton. Do not discard with pack-

ing material.

➆ Screen operates on 110-120V, 60 Hz., 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

General:

When locating viewing surface and checking clear ance for screen's op er a tion,

remember surface is centered in case. Handle case care ful ly to protect ﬁ nish.

Regardless of mounting method, screen should be positively and securely supported

so that vibration or even abusive pulling on the viewing surface will not cause case to

work loose or fall. Installer must insure that fas ten ers used are of adequate strength and

suitable for the mounting sur face chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. "S" hooks, chains (or cable) and

turn buck les should be provided by installer. "S" hooks should go through the rear holes

on the endcap sides (see drawing on page 2), and both ends of the "S" hooks should

be crimped for additional safety. Chains should be attached to beams or other struc tur al

mem bers. Turn buck les should be adjusted so screen hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should furnish

screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may be

mounted as in suspended or wall installation. Optional Ceiling Opening Trim Kit also

available; see diagram on page 2 and separate instruction sheet (included with Ceiling

Opening Trim Kit).

Elec tri cal Con nec tions

Screen operates on 110-120V, 60 Hz., 1.1 amp current draw. Duty cycle: On 28

seconds/Off 4 minutes. Junction box is located inside left endcap and cover plate is

secured to endcap with two screws. Junc tion box contains terminal strip, per wiring

diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire

connecting screen to switch(es) and switch(es) to power supply should be furnished by

installer. Connections should be made in ac cor dance with wiring diagram sup plied, and

wiring should comply with na tion al and local elec tri cal codes. Do NOT wire motors in

parallel.

All operating switches should be "Off" before power is connected.

Operation

CAUTION—Important Instructions: Shipping support brackets must be removed

from each end of dowel during initial operation, before screen is operated in UP

direction. After screen is installed, lower viewing surface to access screws holding

brackets to dowel. Loosen hex head screw, remove bracket and retighten screw at each

end of dowel. Raise and lower viewing surface several times to conﬁ rm satisfactory

op er a tion. If viewing surface does not operate properly, turn power off and check

electrical con nec tions.

Screen Case

Back

Ceiling Tile

(By others)

Form Premier_Inst09-R2 Printed in U.S.A.

Installation Instructions

Caution

Dowel

Please Note: Instructions for adjusting Draper's Tab-Tension System are on page 2.

110-120V Single Station Control—3-position up-off-down switch per mits operation to

be stopped at any point. Factory adjusted limit switches automatically stop screen when

fully down or fully up.

110-120V Multiple Station Control—Switches are similar in ap pear ance to 110-120V

Single Station Control. Screen stops when switch is re leased and may be re start ed in

either direction. Factory adjusted limit switch es stop screen au to mat i cal ly when fully up

or fully down.

24V Control—Three-button up-stop-down switch(es) stop at any point desired, operate

in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen when fully

up or fully down.

Key Operated Switching—Two kinds of key-operated switches are op tion al ly available

with this unit. ➀ The key-operated power sup ply switch controls power to the screen and

switches. When it is "off", the switches will not operate screen. Key may be removed

from the switch in either "on" or "off" position. ➁ A three-po si tion key switch per mits the

screen to be operated directly by key. In this case, the screen's operator must always

have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Limit Adjustments (Standard/Quiet Motors)

Tools needed: Flashlight, small ﬂ athead screwdriver/Allen wrench (4mm or

Screen settings have been factory set as ordered and should not normally require

further adjustment. However, if you ﬁ nd it necessary to adjust for more or less viewing

area, proceed as follows.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing surface

is allowed to run too far up or too far down. When running up, the dowel should

never wrap over the roller. When run to the down limit, a minimum of 1¼ wraps of

fabric must remain on the roller.

The motor limit screws are normally located on the audience left of screen roller, and

the viewing surface rolls off the back of the roller. If the viewing surface is coming off

the front of the roller (motor on left), or the motor is on the audience right of the screen

roller (with viewing surface rolling off the back), reverse the below instructions.

To Reduce Screen Drop

➀ Raise screen surface about 1' above desired setting and turn off.

➁ Turn the DOWN limit screw (I) clockwise (three screw turns = ½ roller revolution).

➂ Test by running screen down and repeat steps 1 and 2 until desired position is

reached.

To Increase Screen Drop

➀ Run screen to the down limit.

➁ With the down switch on, turn the DOWN limit screw (I) counterclockwise (three

turns of screw equals ½ roller revolution) to increase drop.

➂ Test by running screen up about 1' and back down to new down limit.

➃ Repeat steps 2 and 3 until desired position is reached.

CAUTION: At least 1¼ wraps of fabric must remain on the roller when screen is

at the down limit!

Screen is Running Too Far Up

➀ Lower screen surface about 1' below desired setting and turn off.

➁ Turn the UP limit screw (II) clockwise (three screw turns = ½ roller revolution).

➂ Test by running screen up.

➃ Repeat steps 1 through 3 until desired position is reached.

Screen Needs to Run Up More

➀ Run screen down about 1' and turn off.

➁ With the up switch on, turn the UP limit screw (II) counterclockwise (three turns

of screw equals ½ roller revolution).

➂ Repeat steps 1 and 2 until desired position is reached.

CAUTION: Do NOT allow the dowel to wrap up over the roller when the screen

is running up! This could damage the screen.

Shipping

Limit Adjustments (Built-in Low Voltage Motors)

Bracket

➀ Connect the ILT switch to the motor via the terminal blocks, or via the modular port

using four conductor modular cable. When using modular cable, the cable

connectors MUST NOT be crimped in reverse, as with standard telephone cable.

➁ Set the slide switch to the lower position. Press and hold the DOWN button on the

switch to move the viewing surface to the desired lower limit. If the screen moves in

the opposite direction, release the DOWN button and press and hold down the

STOP button for four seconds. This will reverse the operation of the UP and DOWN

switches.

➂ Set the slide switch to the higher position. Move the viewing surface to the desired

upper limit by pressing and holding the UP button on the wall switch.

➃ Return the slide switch to the center position to return to normal operation.

If you encounter any difﬁ culties installing or ser vic ing your Premier screen, call your

dealer or Draper, Inc. Spiceland, In di ana, U.S.A., (765) 987-7999 or fax (765) 987-7142.

"DOWN" LIMIT ADJUSTMENT

"UP" LIMIT ADJUSTMENT

Continued on Page 2

").