Draper E Series Instruções de instalação e funcionamento - Página 2
Procurar online ou descarregar pdf Instruções de instalação e funcionamento para Ecrã de projeção Draper E Series. Draper E Series 4 páginas. 220v ultimate access
Também para Draper E Series: Instruções de instalação e de utilização (4 páginas)
Imprimir página
Silhouette/Series E & V by Draper
To mount suspended from ceiling, the brackets need to be installed on
screen case as noted on page 1. Attach "S" Hooks (supplied) through the
holes in the brackets. Select the set of holes that allows the screen to hang
in a vertical position. The installer is to provide the materials and fasteners
to attach the "S" Hooks to the ceiling. Installer must insure that the fasteners
and suspension material is of adequate strength and suitable for the mounting
surface chosen.
Mounting on 6" extension wall brackets: Special 6" extension brackets are
needed to mount Silhouette ex tend ed from wall. Brackets are not supplied
with screen and must be ordered separately. Specify "Silhouette Extension
Brackets".
Attach right angle adapter to top of extension bracket as shown using (1)
pan head screw and (1) locking nut. Attach (1) "Z" Clip wall mounting bracket
(supplied with screen) to front of extension bracket as shown using (1) pan
head screw and (1) locking nut. (Make sure "Z" Clip is oriented 90° to angle
adapt er.)
Wall mount the ex ten sion brackets to wall, making sure they are level and
vertically plumb. Installer must insure fasteners are of adequate strength and
suitable for chosen mounting surface. Back out the top stop screw until it is
fl ush with front side of angle adapter.
Engage the lip on back of screen case with lip of "Z" Clip and gently pull down
to fully engage case to brackets. Screw in stop screw on each bracket to lock
screen case in place.
Angle adapter
Wall bracket
Extension Arm
Front view of assembled
extension bracket
Removing Case Fascia
Case fascia is removable to access roller assembly. To remove fascia, depress
outward the spring lip located inside lower front corner of screen case and
pull lower corner of fascia outward. Repeat this at right end of case. Support
fascia from center and rotate lower front edge upward approximately 40° to
disengage the Roll-Lok hinge at the top front of screen case. Fascia can now
be com plete ly removed from case.
To install fascia, generally reverse instructions above making sure the Roll-
Lok hinge is completely engaged before rotating fascia down towards the
closed position. Depress spring clips outward, push lower corners of fascia
inward until lips of spring clips hook behind fascia.
Locking screw
Wall bracket*
Angle adapter*
Extension
bracket
*Supplied with screen
90˚
www.draperinc.com
Electrical Con nec tions
Screen operates on 110-120v, 60 Hz. cur rent.
Junc tion box is lo cat ed at left end of screen. It is accessible through front of
screen case after fascia is removed. (See instructions above for removing
fascia.)
Electrical supply wires can enter through the back or top of case. For top
entry, remove plug from top conduit hole and snap plug into hole on back side
of case.
Junction box contains red, black, and white pigtail leads and green internal
ground wire per wiring diagram attached.
If optional low voltage control or video interface control is specifi ed and factory
installed, please refer to wiring diagram on page 3.
Wall or ceiling electrical box should be installed so as to be fully con cealed by
screen case after installation.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire to connect screen to switch(es) and switch(es) to power supply
should be furnished by installer. Con nec tions should be made in ac cor dance
with attached wiring diagram, and wiring should comply with national and
local electrical codes.
All operating switches should be "off" before power is con nect ed.
Operation
Before operating screen, remove any shipping brackets or tape securing fab-
ric and dowel to the roller. If viewing surface hangs out of case 8" or 9", tape
has probable been broken by rough handling in shipment, allowing surface to
"unwrap" one turn off the roller. Manually wrap fabric back around the roller
without turning the roller itself.
When screen is fi rst op er at ed, be cau tious! Cy cle unit down and up sev er al
times to con fi rm sat is fac to ry operation.
110-120v SINGLE STATION CON TROL—3-position UP-OFF-DOWN switch
permits operation to be stopped at any point. Factory ad just ed limit switches
au to mat i cal ly stop screen when fully down or fully up.
110-120v MULTIPLE STATION CONTROL—Switches are similar in ap-
pear ance to 110-120v Single Station Control. Screen stops when switch
is re leased and may be re start ed in either direction. Factory adjusted limit
switches stop screen au to mat i cal ly when fully up or fully down.
24v MULTIPLE STATION CONTROL—Three-button UP-STOP-DOWN
switches stop at any point desired, operate in any sequence. Factory adjusted
limit switches automatically stop screen when fully up or fully down.
110-120v & 12v VIDEO INTERFACE CONTROL—Allows screen to be con-
trolled by a trigger signal—when the signal comes on, the screen descends
automatically. Two versions: Model VIC115 integrates screen operation with
a DRAPER video projector lift or a video projector or tuner with a 110-120v
switch outlet. Model VIC12 interfaces with a 12V switch outlet. Both available
with an override switch (VIC–OS), permitting independent operation. VIC–OS
not available with factory installed VIC115 & VIC12.
KEY OPERATED SWITCH ING—Two kinds of key-operated switch es are
op tion al ly available with this unit.
➀ The key-operated power supply switch controls power to the screen and
switches. When it is "off", the switches will not operate screen.
Key may be removed from the switch in either "on" or "off" position.
➁ A three-position key switch permits the screen to be op er at ed directly by
key. In this case, the screen's operator must always have a key.
Adjustments
CAUTION: Be sure all switches are in "off" position before ad just ing limit
(765) 987-7999
Page 2 of 4