Draper CS14A Manual de instruções - Página 4
Procurar online ou descarregar pdf Manual de instruções para Serra Draper CS14A. Draper CS14A 16 páginas. 350mm chop saw
Também para Draper CS14A: Manual de instruções (12 páginas)
Imprimir página
SAFETY WARNING
WARNING
Please read the following instructions carefully, failure to do so could lead to serious personal injury.
IMPORTANT
This machine was designed for metal cutting applications only. Draper Tools Limited recommends that this
machine should not be modified or used for any application other than that for which it was designed. If
you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.
GENERAL SAFETY INSTRUCTIONS FOR MACHINE TOOLS
1.
KNOW YOUR MACHINE TOOL
Read and understand the owner's manual and
labels affixed to the tool. Learn its application and
limitations as well as the specific potential hazards
peculiar to this tool.
2.
EARTH ALL TOOLS
This tool is equipped with an approved 3-core
cable. The green and yellow conductor in the core
is the earth wire. Never connect the green and
yellow wire to a live
terminal.
3.
KEEP GUARDS IN PLACE
and in working order.
4.
REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
5
KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.
Floor must not be slippery due to oil or sawdust.
6.
AVOID DANGEROUS ENVIRONMENT
Do not use power tools in damp or wet locations or
expose them to rain. Keep work area well lit.
Provide adequate surrounding work space.
7.
KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area.
8.
MAKE WORKSHOP CHILDPROOF
- with padlocks, master switches, or by removing
starter keys.
9.
DO NOT FORCE TOOL
It will do the job better and safer at the rate for
which it was designed.
10. USE RIGHT TOOL
Do not force tool or attachment to do a job for
which it was not designed.
11. WEAR PROPER CLOTHING
Do not wear loose clothing, gloves, neckties or
jewellery (rings, wristwatches) to catch in moving
parts. NON SLIP footwear is recommended. Wear
protective hair covering to contain long hair. Roll
long sleeves above the elbow.
12. USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with BS 2092)
at all times. Normal spectacles only have impact
Continued ...
resistant lenses, they are NOT safety glasses. Also,
use face or dust mask if cutting operation is dusty
and ear protectors
(plugs or muffs) during extended periods of
operation.
13. SECURE WORK
Use clamps or a vice to hold work. This free
both hands to operate tool.
14. DO NOT OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
16. DISCONNECT POWER TO THE TOOLS
Before servicing, when changing accessories
such as cutters etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in 'OFF' position before
plugging in cable to the power supply.
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories. Follow the instructions that
accompany the accessories. The use of
improper accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if
the cutting tool is accidentally contacted.
Do not store materials above or near the tool
such that it is necessary to stand on the tool to
reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
ensure that it will operate properly and perform its
intended function. Check for alignment of moving
parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
22. NEVER LEAVE MACHINE RUNNING
UNATTENDED
Turn power off. Do not leave machine until it
comes to a complete stop.
- 2 -