Draper Crank-Operated FlexShade Instruções de instalação - Página 2
Procurar online ou descarregar pdf Instruções de instalação para Mobiliário de interior Draper Crank-Operated FlexShade. Draper Crank-Operated FlexShade 2 páginas.
Imprimir página
Crank-Operated FlexShades by Draper
Surface (Ceiling/Wall) Headbox or Large Pocket Headbox
➀ Snap endcap covers onto endcaps.
➁ Place endcaps into back/top portion of wall/ceiling headbox or into pocket
extrusion of large pocket headbox. Using pre-drilled holes in endcaps, mark
the headbox for drilling.
Caution: Before mounting shades, verify measurements on the card
provided with the shade, and ensure the brackets are installed at the
correct width.
➂ Drill holes in back or top, depending on whether you will be mounting the
headbox to the wall or ceiling, or in a pocket.
➃ Attach endcaps and wall/ceiling headbox back/top or large pocket headbox
extrusion to wall, ceiling or pocket using mounting hardware appropriate for
site conditions.
➄ Install shade following steps 3 through 5 under "Crank Operated Flex-
Shades—Fascia".
➅ Attach headbox fascia or pocket closure (see Fig. 7).
Surface Headbox
STEP 1
Large Pocket Headbox
STEP 1
➆ Re-attach crank handle (see Fig. 6, page 1). Make sure the headbox fascia
or pocket closure is in place before attaching crank handle, so that the
screws attach both the handle and the fascia to the endcap.
Small (3¼" Hardware) Pocket Headbox
➀ Snap endcap covers onto endcaps.
➁ Place endcaps into pocket extrusion of small pocket headbox. Using pre-
drilled holes in endcaps, mark the headbox for drilling (see Fig. 8).
Caution: Before mounting shades, verify measurements on the card
provided with the shade, and ensure the brackets are installed at the
correct width.
7
1
/
"
8
3
3
/
"
4
7
1
/
"
8
1
1
/
"
4
STEP 2
STEP 2
STEP 3
Figure 7
1
3
/
"
4
2"
5
/
"
16
2"
2"
1
1
/
"
4
1
2
/
"
2
Figure 8
www.draperinc.com
➂ Drill holes in back or top, depending on how you will be mounting the small
pocket.
➃ Attach endcaps and small pocket headbox extrusion to wall, ceiling or in
pocket using mounting hardware appropriate for site conditions.
➄ Remove crank handle assembly from crank (operator) endcap (see Fig. 4
—note: there are no washers with small pocket headbox crank operators).
Insert shank into hole in center of crank assembly, then slide fabric/roller
onto shank (see Fig. 2).
➅ Slide notched pin into idler endcap (see Fig. 9).
Be sure retainer
clip is installed.
➇ Attach small pocket closure (see Fig. 10).
Small Pocket Headbox
➈ Re-attach crank handle assembly (see Fig. 6, page 1).
Field Adjustments
Each Draper Solar Control Shade is tested to ensure proper operation.
Even with this testing, some fi eld adjustments may be needed for telescoping.
If the shade is telescoping, place a piece of high quality gaffer tape about 1"
wide on the exposed roller (where the fabric will cover it) on the side that you
want the fabric drawn toward. For example: if the fabric is tracking to the left,
place the tape on the right side.
Cleaning and Maintenance
Window covering products manufactured by Draper, when properly
installed, should require no operational maintenance or lubrication.
Most of Draper's standard fabrics may be cleaned at the window by
vacuuming with a soft brush attachment. They may also be cleaned by using
a sponge or soft cloth and mild solution of warm soapy water. A dishwashing
liquid, such as Ivory liquid, is recommended. A clean dry cloth is recommend-
ed for the metal fi nish. Exceptions are Flocké, Roc-Rol, Obion and Phifer
SW7000 fabrics, which must be cleaned with a dry art sponge.
(765) 987-7999
Page 2 of 2
Figure 9
Secure closure
panel to endcap
with screw
Figure 10