Draper FlexShade Zip with Crank Manual de instruções de instalação - Página 3

Procurar online ou descarregar pdf Manual de instruções de instalação para Mobiliário de interior Draper FlexShade Zip with Crank. Draper FlexShade Zip with Crank 6 páginas.

Imprimir página

FlexShade

Zip with Crank by Draper

Mounting Headbox - Zip 127 Angled Headbox

The FlexShade Zip 127 Angled Headbox can be mounted permanently to the

wall or ceiling (See Mounting Headbox - Permanently to Ceiling or Wall on

page 1); or the Headbox can rest atop the Side Channels and is held in place

there by two mounting studs coming down from the endcaps.

PLEASE NOTE:

Steps 1-5 of the Mounting Side Channels

section must be completed before mounting

the Zip 127 Angled Headbox. It is critical that

the full length of each Side Channel

is secured to the mounting surface.

1 Remove screws from bottom of Headbox,

remove Fascia and set aside. (See Fig. 11).

HEADBOX

MOUNTING

STUD

S i

d e

C h

a n

n e

Figure (12)

3 Insert "Zippers" on the side of the Hem Bar into the fabric retainers in the

Side Channels (See Fig. 12).

4 Insert Headbox mounting stud into Side Channel (See Fig. 12).

5 Return Fabric Retainers to Side Channels and re-attach Covers.

FlexShade Zip 127

6¼" (

158mm)

Figure (11)

5" (

127mm)

(

127mm)

7¼"

(

183mm)

REMOVE

FASCIA

2 Insert "Zipper" on one side of

the Hem Bar into the fabric

retainer in the Side Channels

(See Fig. 12).

HEADBOX

MOUNTING

ZIPPER

STUD

HEMBAR

FABRIC

S i

RETAINER

d e

C h

STRIP

a n

n e

www.draperinc.com

Pocket Installation

The FlexShade Zip can also be installed in a pocket in the ceiling. You must

provide adequate clearance for removal of the Roller Assembly during

installation and maintenance.

FlexShade Zip 92

4 ¾"

(120mm)

(92mm)

(148mm)

Figure (13)

The minimum depth of the ceiling pocket for the FlexShade Zip 92 is 4¾"

(120mm), and for the FlexShade Zip 127 is 6¼" (158mm). See Fig 13 below.

Alternate Mounting for Jamb Recessed

Installations (Zip 127 Angled Only)

If the system is installed in a recess, it is unlikely that there will be sufficient

space above the side channels to allow the Headbox to be mounted onto them.

In these instances follow the steps for preparing the system (See Mount-

ing Headbox - Zip 127 Angled Headbox). Then mount the Headbox onto

the side channels and present the entire system into the opening. Hold the

system in position and use appropriate screws to fix the side channels in

place. Apart from this, the other steps should be followed as described.

Attaching Anti-Insect Brush Seals (Optional)

The FlexShade Zip has optional Anti-Insect Brush

Seals pre-installed along the width of the fascia.

There are also brush seals supplied for each of

the side channels that will need to be installed.

Remove the double-sided tape and apply to the

side channels as shown at right (Fig. 15).

Cleaning and Maintenance

Window covering products manufactured by Draper, when properly

installed, should require no operational maintenance or lubrication.

Most of Draper's standard fabrics may be cleaned at the window by

vacuuming with a soft brush attachment. They may also be cleaned by using a

sponge or soft cloth and mild solution of warm soapy water. A dishwashing liq-

uid, such as Ivory liquid, is recommended. A clean dry cloth is recommended

for the metal finish.

(765) 987-7999

Page 3 of 6

FlexShade Zip 127

6¼" (

158mm)

5" (

127mm)

(

Insect Barrier

Brush Seal

Figure (15)

127mm)

7¼"

(

183mm)