Draper Techmatic Window Shade Instruções de instalação e operação - Página 4
Procurar online ou descarregar pdf Instruções de instalação e operação para Mobiliário de interior Draper Techmatic Window Shade. Draper Techmatic Window Shade 4 páginas.
Imprimir página
Techmatic Window Shades
Section 3 - Bead Chain Limits and Safety Device Installation
Section 3.1 - Attaching Stop Balls
1. Set upper and lower travel limits by installing stop balls to bead chain
Section 3.2 - P-Clip Cord Tension Device
Please Note: Draper Bead Chain Clutch Operated shades that do not comply with WMCA/ANSI Standard
A100.1-2018 come with a cord tension device in a separate kit that dealer MUST install
Spring loaded tensioner is preattached to bead chain
as the P-clip must be attached to wall, jamb or sill so that bead chain is held taut enough that
children cannot pull it away from wall or fit their head into loop.
Section 3.3 - Spring-Loaded Cord Tension Device
If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2012, a Spring-Loaded Cord
Tension Device comes installed on bead chain
mechanical fasteners
(wood screws)
away from wall or fit their head into loop.
For more information, visit
www.draperinc.com/WindowShades/WCMAcompliance.asp.
Please Note: Overtightening screws will damage Spring Loaded Tension Device.
Section 4 - Endcaps with Fascia
Section 4.1 - Attaching Fascia to Endcaps
Place groove along top of fascia over endcaps, and snap into place
the correct distance apart for fascia to be properly attached with full engagement. Fascia is not fully seated
until it clicks into place on both ends. Once in place, check for secure fit. If not secure, secure with appropriate
fastener
(not
included).
Section 4.2 - Reverse Roll Fascia
1. Slide endcaps into extrusions.
2. Using provided holes in endcaps, mark the fascia for drilling.
3. Attach endcaps to fascia.
4. Mount Endcaps/Reverse Roll Fascia.
5. Install roller/fabric/operator assembly according to relevant instructions.
6. Attach endcap covers to endcaps. Use double-sided tape to help secure in place.
Section 5 - Surface Headbox or Pocket Headbox
Caution: Before mounting shades, verify measurements on card provided with shade, and ensure unit is
installed at correct width.
Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
1. Snap endcap covers onto endcaps.
2. Slide endcaps into the top/back portion of surface headbox or into pocket extrusion
of headbox. Using provided holes in endcaps, mark headbox for drilling.
(wall mount)
3. Drill holes in back
4. Attach endcaps and Surface Headbox back/top or Pocket Headbox extrusion to wall,
ceiling or pocket using mounting hardware appropriate for site conditions.
(See Section 4.1 - Mounting Endcaps for
5. Install shade
6. Attach headbox fascia or pocket closure
Note on surface style headbox: Fascia is not fully seated until it clicks into place on both ends. Once in place, check
for secure fit. If not secure, secure with appropriate fastener
(Fig.
9). An approved permanent warning label and approved
are included. Device is designed so that children cannot pull bead chain
(See safety note on page
2).
(ceiling mount)
or top
of top/back cover or pocket headbox.
Fascia).
(Fig.
12).
®
(crimp closed using pliers) (Fig.
(Fig.
9). Spring loaded tensioner as well
(Fig.
10). Endcaps must be installed
(not
included).
Figure 7
7).
Attach
Stop Balls
(Fig.
8).
Crimp
Closed
with
Pliers
Sill
Mount
ATTACHING FASCIA
Fascia Attachment Small & Large Endcaps
STEP 1:
ENDCAP
Figure 10
Figure 11
ATTACHING CLOSURE PANEL
Large Pocket Headbox
Small Pocket Headbox
STEP 1
STEP 1
STEP 2
STEP 2
STEP 3
STEP 3
Secure to Endcap
with Screw
Figure 12
page 4 of 4
Figure 8
Figure 9
Jamb
Mount
Tensioner
STEP 2:
ENDCAP
Clicks into place
Large Pocket Headbox
Small Pocket Headbox
STEP 1
STEP 1
STEP 2
STEP 2
STEP 3
STEP 3
Secure to Endcap
with Screw