Bosch CDG634B.1 Manual de instruções - Página 26
Procurar online ou descarregar pdf Manual de instruções para Forno Bosch CDG634B.1. Bosch CDG634B.1 36 páginas.
Imprimir página
Trouble shooting
en
Buttons flash
Liquid in the evaporator dish has fully
evaporated, even though the water
tank is full
The water tank empties for no dis-
cernible reason. The evaporator dish
overflows
The appliance's display prompts you
to fill up the water tank even though it
is full.
The appliance's display prompts you
to fill up the water tank even though it
is not yet empty, or the water tank is
empty but no corresponding message
appears on the display
When you cook with steam, a lot of
steam is produced
When cooking with steam, a lot of
steam is produced repeatedly
Steam escapes from the ventilation
slots during cooking
--------
:
Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Error messages on the display
When an error message appears on the display with "D"
or "E", e.g. D0111 or E0111, switch the appliance off
and on again using the ÿ On/Off button.
If it was a one-off error, the display goes out. If the error
message appears again, call the after-sales service and
quote the exact error message.
Replacing the cooking compartment bulb
Heat-resistant 230 V/25 W halogen bulbs with seals are
available from the after-sales service. Please specify the
E number and FD number of your appliance.
:
Warning
Risk of electric shock!
When replacing the cooking compartment bulb, the
bulb socket contacts are live. Before replacing the bulb,
unplug the appliance from the mains or switch off the
circuit breaker in the fuse box.
26
EURO Appliances - euappliances.info
Normal occurrence caused by
condensation behind the con-
trol panel
The water tank has not been
inserted properly
The feed line to the water
tank is blocked
The water tank was not
closed properly
The tank lid seal is dirty
The tank lid seal is faulty
The water tank has not been
inserted properly
The detection system is not
working
The water tank is dirty.The
moving water level indicators
are jammed
The appliance is being auto-
matically calibrated
The appliance is unable to cal-
ibrate itself automatically if
cooking times are too short
Normal procedure
As soon as the condensation has evaporated, the buttons no longer flash
Push in the water tank completely until you feel it engage
Descale the appliance
Check the set water hardness range and change it, if necessary
Close the lid until you feel it lock into place
Clean the seal
Obtain a new water tank from the after-sales service
Push in the water tank completely until you feel it engage
Call the after-sales service
Shake and clean the water tank. If the jammed parts cannot be freed, obtain a
new water tank from the after-sales service
Normal procedure
Reset the appliance to the factory settings and repeat the calibration process
Not possible
:
Warning
Risk of burns!
The appliance becomes very hot. Never touch the
interior surfaces of the cooking compartment or the
heating elements. Always allow the appliance to cool
down. Keep children at a safe distance.
Unplug the appliance from the mains or switch off
1.
the circuit breaker in the fuse box.
Turn the cover anti-clockwise to remove it.
2.
Remove the bulb.
3.
Insert the new bulb, making sure that the pins are in
the correct position.Push the bulb in firmly.
Caution!
Only operate the appliance with the glass cover and
seals.
Slide the new seals and the clamping ring onto the
4.
glass cover in the right order.
Screw the glass cover with the seals back on again.
5.
Connect the appliance to the power supply and
6.
carry out commissioning again.