1RC Racing 18th Midget 2.0 Manual de início rápido/Manual de instruções - Página 8

Procurar online ou descarregar pdf Manual de início rápido/Manual de instruções para Carro de brincar motorizado 1RC Racing 18th Midget 2.0. 1RC Racing 18th Midget 2.0 16 páginas.

Imprimir página
ESC (Electronic Speed Control)
WARNINGS
- USER MUST READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS AND PRECAUTIONS.
- ENSURE ALL WIRES AND CONNECTIONS ARE WELL INSULATED BEFORE CONNECTING THE ESC/Rx TO RELEATED DEVICES, AS SHORT CIRCUIT WILL DAMAGE THE ESC/Rx.
- ENSURE ALL DEVICES ARE WELL CONNECTED TO PREVENT POOR CONNECTION THAT MAY CAUSE YOUR VEHICLE TO LOSE CONTROL OR OTHER UNPREDICATABLE ISSUES SUCH AS DAMAGE TO THE DEVEICE.
- STOP USING THE ESC WHEN IT TEMPERATURE EXCEEDS 90°C/194°F, OTHERWISE YOUR ESC/Rx WILL BE DAMAGED AND MAY ALSO DAMAGE YOUR MOTOR. WE ALWAYS RECOMMEND SETTING THE "OVER
HEAT WARNING" TO "ENABLED" TO ENSURE DAMAGE DOES NOT OCCUR TO YOUR ESC/Rx UNIT.
- ALWAYS DISCONNECT THE BATTERIES AFTER USE, AS THE ESC WILL CONTINUE TO CONSUME CURRENT IF IT'S CONNECTED TO BATTERIES (even if the esc is turned off). LONG-TIME CONNNECTION WILL CAUSE
BATTERY TO COMPLETELY DISCHARGE AND RESULT IN DAMAGE TO BATTERIES AND/OR ESC. THIS WILL NOT BE COVERED UNDER WARRENTY.
Setting ESC
1.
Ensure battery is installed and ensure battery is connected to model and secured in battery tray area. Ensure battery is connected
correctly or damage can occur to ESC/Rx unit.
2.
Remove hood on model so you have full access to ESC/Rx unit.
3.
Ensure car is elevated off ground so tires are not touching ground, this will prevent any damage if car starts to move during binding
process.
4.
On transmitter, make sure the throttle trim knob is set to 0, then turn on transmitter.
5.
Hold ESC Set Button down while you turn on the model using the switch just behind the front axle from underside of model.
6.
When ESC Red Light starts to flash, release the Set Button, ESC is now in setup mode.
7.
With trigger on radio in neutral position, press Set Button one(1) time, ESC Red Light will stop flashing and green light will quickly flash
once, this confirms the neutral position.
8.
Now pull trigger to full throttle on transmitter and press Set Button again, ESC Green Light will flash twice to confirm full throttle setting,
hold trigger in full throttle until light stops flashing.
9.
Now push trigger to full brake on transmitter and press Set Button again, ESC Green Light will flash three time to confirm full brake setting,
hold trigger in full brake until light stops flashing.
10.
Return trigger on transmitter to neutral and ESC Green Light will brink two times. Your ESC and now set.
11.
Ensure steering and throttle works correct, make adjustment to transmitter throttle trim knob so motor does not move when trigger on
transmitter is in neutral position.
12.
Ensure ESC it reaching full throttle, pull trigger to full throttle and ESC Green Light should go solid if full throttle is reached.
13.
If throttle does not work correct, go back to step 1 and repeat steps 1-12.
LED LIGHT STATUS—During Startup
- RED LED keeps flashing rapidly indicating ESC does not detect correct throttle signal/neutral value stored in ESC that match Radio setting.
Rotate Throttle Trim knob on radio until light stops flashing.
LED LIGHT STATUS—During Operation
- RED & GREEN LED's die out when throttle trigger is in throttle neutral zone.
- RED LED turns solid when your vehicle starts to run forward, GREEN LED will also come on when pulling trigger to full (100%) throttle.
- RED LED turns solid when you apply brake.
- RED LED turn solid when you reverse your vehicle.
LED LIGHT STATUS—Protection Warnings
- RED LED flashes a short single flashes that repeats 3 times indicating low voltage cutoff protection is activated.
- GREEN LED flashed in short single flashes that repeats 3 times indicating the ESC thermal/overheat protection is activated.
This ESC unit has advanced settings that can be adjusted. Visit www.1RC-Racing.com for further details on how these settings can be adjusted.
ESC Red
Light
ESC Green
ESC Set
Light
Button
8