Anchor Beacon Manual do Proprietário - Página 4

Procurar online ou descarregar pdf Manual do Proprietário para Altifalantes Anchor Beacon. Anchor Beacon 4 páginas. Anchor beacon line array battery-powered, portable line array sound system
Também para Anchor Beacon: Manual do Proprietário (4 páginas), Manual do Proprietário (10 páginas), Manual do Proprietário (7 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas), Manual de início rápido (2 páginas)

Imprimir página

BAsic sYstem oPerAtion

note: FuLLY chArGe BAtteries BeFore First use!

1. REMOVE TRAVEL DOLLY (PAGE 3) AND OPEN LINE ARRAY (BELOW)

2. Set all Input Levels to minimum & Tone Controls to flat (middle) set-

ting

3. Plug wired microphone into the MIC 1 or MIC 2 jacks and/or any au-

dio source into the LINE-IN jacks

4. Switch POWER to "ON", Power ON LED will light

5. Slowly increase Level Controls for active Input Jacks to desired volume

6. Adjust Tone Controls for desired sound quality

imPortAnt: make all connections w/ shielded

cables to avoid hum, buzzing or interference.

need more heLP? visit our Website:

www.anchoraudio.com

Line ArrAY toWer

oPeninG BeAcon Line ArrAY

1. Open Array latches

2. Grasp handle and remove Array from base

3. Turn Array over and place on top of base

4. Close Array latches

5. Slowly flip Array Tower up until locked

securely into place

imPortAnt: Latches must

be locked and grill must

face forward for system to

work!

cLosinG BeAcon Line ArrAY

1. Turn POWER to "OFF"

2. Fold Array in half (apply slight pres-

sure)

3. Open latches and remove folded Array

4. Turn Array over grasp handle and slide

into base

5. Close Array latches

BeAcon sound sYstem

controL PAneL

model shown: BeA-7500mu2

mP3 PLAYer

WireLess receivers

Line out – outPut JAcK

Balanced 1/4" & Dual RCA provide a combined

output of all active system inputs.

Record your presentation or connnect to another

powered sound system.

universAL mic – inPut JAcKs

Balanced XLR – low impedance, for balanced mic,

powers condenser-type mics.

Unbalanced 1/4" – high impedance, for unbalanced

mics, no phantom power.

usB dc out -

To charge/power external device

dc out - 5V 500 mA

To charge/power external device

BuiLt-in BAtterY mAintenAnce

To preserve battery life the built-in batteries MUST be FULLY charged before the first

use. Regardless of length of operation, it is recommended that batteries be fully

charged as soon as possible after each use.

Ac oPerAtion & BAtterY chArGinG

Beacon Sound Systems include an automatic charging system designed to properly

charge and maintain the systems built-in batteries. To charge batteries plug the system

into an AC outlet and operate as normal while built-in batteries are charging. The

CHARGE STATUS LED will light when charging. Bright red indicates charge process has

begun. Amber indicates the charge process is almost complete, and green indicates

full battery. It takes approximately 7 hours to charge the completely drained Beacon

batteries.

BAtterY service time

Fully charged batteries will yield approximately 6 – 8 hours of continuous music at

medium volume level (2 – 4 hours at full volume or longer for speech only) . However

service times vary depending on control settings and use of accessories.

TRACK +

ALBUM +

TRACK -

ALBUM -

MP3 PLAYER

(see page 6)

SD CARD

(see page 6)

LINE IN

WIRELESS 1

WIRELESS 2

LINE OUT

VOLUME

Beacon

MADE IN THE USA

Anchor Audio, Inc.

800/ANCHOR1

www.anchoraudio.com

5V 500mA

DC OUT

12V 500mA

CHARGE STATUS

BATTERY EMPTY

WARNING: TO REDUCE THE RISK OF FIRE

12V 500 mA

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS EQUIPMENT TO RAIN OR MOISTURE.

POWER INLET

POWER

100-240 VAC / 47-63 HZ

(250 WATTS MAX)

OFF

Ac PoWer cord inLet

PoWer sWitch

BAtterY rePLAcement

The batteries must be replaced every 2 – 3 years depending on usage over time. Call Anchor

Audio at 800.262.4671 to order batteries.

To replace your batteries you will need a Phillips screwdriver and follow these procedures:

1. Be sure the power switch is in the OFF position.

2. Remove the screws in the lower cover panel of the Beacon.

3. Gently slide the cover panel with the battery tray out of the case.

4. Unclip each battery connection cable and remove the batteries from the tray.

5. Connect each new battery to the connection cable, attach plate to the tray and slide

the tray into the Beacon.

6 Replace each screw in the cover panel.

sYstem storAGe & BAtteries

Fully charge batteries before storage. For extended periods of storage either leave system

plugged into an AC outlet or charge the system at least once each month for a minimum

of 24 hours.

note: system can Be used during charging!

Line in – inPut JAcKs

The 1/8 (3.5mm) jack is used to hook up

a portable CD player, iPod, laptop or other

external audio source.

REPEAT

MUTE

Dual RCA unbalanced inputs can be used

MODE

POWER

for daisy-chaining together multiple Beacon

AUX IN

speakers.

Line in LeveL controL

LINE IN

MP3

VOLUME

tone controLs – BAss/treBLe

BALANCED

microPhone LeveL controLs

TREBLE

BASS

voice over Button

MIC 1

VOLUME

Reduce Line and CD Input levels by 12dB when

MIC 1

using microphones allowing speakers to be heard

MIC 2

over background music.

VOLUME

ON = Button In

OFF = Button Out

MIC 2

VOICE

OVER

chArGe stAtus Leds

Green - Charge complete

Amber - Charge nearly complete

Red - Charging has begun

POWER ON

Battery empty Led

Red - charge battery immediately

Power on Led

Green - power on