Bosch 1775E Manual de instruções de funcionamento/segurança - Página 9
Procurar online ou descarregar pdf Manual de instruções de funcionamento/segurança para Ferramenta eléctrica Bosch 1775E. Bosch 1775E 33 páginas. Tuckpointing grinder
Também para Bosch 1775E: Brochura (34 páginas), Lista de peças (2 páginas), Manual de instruções de funcionamento/segurança (37 páginas)
Imprimir página
BM 3609929818 3/03
3/10/03
SLIDE ON-OFF SWITCH WITH LOCK
The tool is switched "ON" by the switch
button located at the side of the motor
housing. The switch can be locked in the
"ON" position, a convenience for long
grinding operations.
TO TURN THE TOOL "ON" without locking
it, slide the switch button forward by
applying pressure ONLY at the REAR
portion of the button. When pressure is
released the switch button will snap to
"OFF" position.
TO LOCK THE SWITCH "ON", slide the
switch button forward and press "IN" the
FRONT portion.
TO UNLOCK THE SWITCH, simply press
and release the REAR portion of the button.
Switch is spring loaded and will snap back
automatically.
Hold the tool with both
WARNING
!
hands while starting the
tool, since torque from the motor can cause
the tool to twist.
Start the tool before applying to work and let
the tool come to full speed before
contacting the workpiece. Lift the tool from
the work before releasing the switch. DO
NOT turn the switch "ON" and "OFF" while
the tool is under load; this will greatly
decrease the switch life.
CONSTANT RESPONSE CIRCUITRY
The internal electronic feedback system
provides a "soft start", which will reduce the
stresses that occur from a high torque start.
The system also helps to keep the no load
speed virtually constant between no-load
and load conditions.
OVERLOAD PROTECTION
Your tool is equipped with overload
protection to protect the motor. If the tool
stops during operation TURN OFF SWITCH
IMMEDIATELY and allow the motor to cool
for about 30 seconds by running at no-load.
If the overload protection stops the tool
repeatedly, excessive force is causing the
tool to overload. Don't press so hard and let
the tool do the work.
SERVICE MINDER™ BRUSHES
Eliminates quess work, stops the tool when
preventive maintenance is required.
8:42 AM
Page 9
Operating Instructions
ADJUSTABLE DEPTH STOP
Your tool is equipped with an adjustable stop.
Your cutting depth can be pre-set and/or
repeated by using the depth stop (Fig. 1).
1. Loosen the depth stop lock knob.
2. Depress stop button, move to desired
position on depth bracket, and release button
to secure stop in place.
3. Place foot against workpiece, push down on
tool until it stops.
4. To secure and hold foot and guard
assembly at desired depth of cut. Move foot to
desired depth of cut and securely tighten the
depth stop lock knob.
WARNING
!
abrasive wheels. Always keep wheel guard
between you and your work while grinding.
Position the wheel guard such that the dust
port does not interfere with the On/Off
switch.
To adjust guard, loosen clamp screw and
rotate guard to desired position, and
securely tighten screw. Always keep the
wheel guard between you and your work
when during operation.
WARNING
!
system. In addition, always wear approved
dust mask.
Your tool is equipped with a dust port for
dust extraction. To use this feature, insert
adapter into dust port (Fig. 2), then insert
vacuum hose (optional accessory) into the
adapter and connect the opposite end of the
hose to a shop vacuum cleaner.
Always make sure the vacuum cleaner that
you use is designed for extraction of
masonry dust.
The auxiliary handle, used to guide and
balance the tool can be bolted to either side
of the spindle housing depending on
personal preference and comfort. Always
use the auxiliary handle for maximum control
and ease of operation.
-9-
WHEEL GUARD
Wheel
guard
must
attached
when
using
DUST EXTRACTION
This tool must only be used
with a dust extraction
AUXILIARY HANDLE
be