Dreamline ENIGMA Manual de instalação - Página 4

Procurar online ou descarregar pdf Manual de instalação para Luminárias de casa de banho Dreamline ENIGMA. Dreamline ENIGMA 12 páginas. Shower door
Também para Dreamline ENIGMA: Instruções de instalação (12 páginas)

Imprimir página

Installation

1. Select the proper place to install the shower enclosure. Refer to the shower enclosure plan

for dimensions. Mark out the threshold position on the floor. See fig. 1 for details.

2. Locate the Threshold (15) in the package and place it to the desired position. Mark the

holes for drilling on the floor. Remove the threshold, drill the holes in the floor and insert

Small anchors 5/16" (18). Apply silicone on the bottom of the Threshold, place it back into

the chosen position and attach it to the floor with Countersunk screws ST4.2×30 (16). See

fig.2 for details.

3. a) Take the Return glass panel (22) and the Wall & Bottom Brackets for Return Glass

(19). Attach the brackets to the glass. See fig. 3&4 for details.

Note: Parts of the Wall & Bottom Return Glass Brackets with the mounting holes should face

inward so that when the glass panel is in place, mounting bolts are only visible from the inside.

b) Refer to the shower enclosure plan for dimensions and mark them out on the wall.

Position the glass according to the dimensions provided in the diagram against the end of

the Threshold. Level the return glass performing necessary adjustments to ensure that the

return glass is parallel to its opposite wall and square against the back wall. See fig. 5 for

details.

c) Mark the bracket position. Detach the Glass Brackets from Return glass panel. Using

brackets mark mounting holes for drilling (two on the wall and one on the floor), and then drill

the holes. Insert Small anchors 5/16" (18). Secure the wall mounting part of the brackets to

the wall with Screw ST4.2×30 (21). See fig. 6&7 for details.

d) Set the Return glass panel against the installed wall mounting parts of the bracket from

outside and secure it to the fastening bracket parts with bolts and gaskets provided. See fig.

8 for details.

Before you install the Front stationary glass panel (02), you have to take the Sliding

door (05) into the shower room and lean it on the wall.

4. Attach the Running rail (03) to the Front stationary glass panel (02) with preinstalled

Glass brackets (07). Slide the Stoppers (01) from each end of the running rail and

temporarily secure them on the rail. Then slide the Wall brackets (08) on each end of the

Running rail and temporarily secure them as well. See fig. 9&10 for details.

5. a) Attach the Glass connector (20) to the Return glass panel. See fig. 11-3. Place the

Front stationary glass panel on the threshold and push the bottom edge into the groove of

the Threshold. Push the Stationary glass panel against the wall. Loosen the Wall bracket

to attach the Running Rail to the Glass connector on the Return Glass panel. (Please

note that the Running rail should now be inside the enclosure) See fig. 11 for details.

b) Level the glass and the Running rail. If a horizontal adjustment is required, adjust it in the

Glass brackets and the Glass connector. See fig. 12 for details.

c) When the Front stationary glass and the Running rail had been leveled, slide the Wall

bracket on the rail against the wall and mark its position with a pencil. Remove the glass

panel. Using the Wall bracket mark the hole for drilling on the wall and drill the hole. Insert

the Large anchors 3/8" (9) and screw the male part of Wall bracket onto the wall using the

Round head screw ST6×45 (10) (you only need to use one of the two male parts detached

from the wall brackets).

d) Apply a small amount of silicone along of the Threshold channel. Place the Front

stationary glass back in position and attach the Wall brackets to the male part on the wall

and on the Return glass panel. Tighten the fastening set-screws with provided Allen Key

on the Wall brackets to secure the Running rail. See fig. 14 for details.

Rev. 1.1.