Bosch ANGLE EXACT ION 18 V-LI Instrução original - Página 9
Procurar online ou descarregar pdf Instrução original para Perfurar Bosch ANGLE EXACT ION 18 V-LI. Bosch ANGLE EXACT ION 18 V-LI 13 páginas. 15-500; 23-380; 30-290; 30-300; 40-220; 50-210; 60-120; 8-1100
OBJ_BUCH-1521-004.book Page 18 Friday, December 6, 2013 8:19 AM
18 | English
Assembly
Before any work on the power tool, remove the battery.
Battery Charging
Use only the battery chargers recommended by Bosch
for this power tool. Only these battery chargers are
matched to the lithium ion battery used in your machine.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 14 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 9, press the unlocking button 14
and pull out the battery toward the front. Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Battery Charge-
Meaning
control Indica-
tion 8
Flashing light +
Battery Charging:
audio signal
Only 6 –8 more screwdriving operations
possible.
Continuous light Capacity no longer sufficient for a new
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
Flashing light
The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
1 609 92A 0CM | (6.12.13)
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative
humidity between 20 and 95 %, free of moisture condensa-
tion.
Suspension Device (see figure B)
With the utility clip 15, the machine can be attached to a sus-
pension device.
– Fasten the utility clip 15 to the machine by engaging it into
the fastening slots 16.
Depending on the machine's centre of gravity, either the
front or rear slots can be used.
Regularly check the condition of the utility clip and the
hook of the suspension device.
Adjusting the Worklight (see figure C)
– Press off the marking ring 17 with a thin screwdriver blade,
a knife, or similar.
– Using snap-ring pliers, slide the snap ring 18 toward the
rear onto the housing shell.
The two shell halves of the LED holder 12, which enclose the
worklight 13, can now be adjusted to any desired position.
– Pay attention not to damage the worklight cable and, with-
out kinking or bending it, slide it into the cavity 19 intend-
ed for it in the housing shell.
– Enclose the worklight 13 again with the two housing shells
of LED holder 12.
– Press the snap ring 18 and the marking ring 17 back to
their initial positions.
Mounting the Angled Screw Head (see figure D)
Applies for the fol-
ANGLE EXACT ION
lowing types:
8-1100 | 15-500 | 23-380 | 30-290
On these industrial cordless angle wrenches, a fitting angled
screw head (see "Angled drive head", page 17) has to be
mounted first.
– Hold the power tool with the open-end spanner 21 by the
spanner flats 4 of the angled head flange.
Never clamp the tool by the housing shells!
– Mount the angled screw head 3 onto the flange in the re-
quested position and tighten the sleeve nut with the open-
end spanner 20 via the spanner flats 5.
Hold the angled head flange with the open-end spanner 21
to prevent turning.
Adjusting the Angled Drive Head
The angled drive head 3 can be adjusted to a total of eight po-
sitions.
– Hold the power tool with the open-end spanner 21 by the
spanner flats 4 of the angled head flange.
Never clamp the tool by the housing shells!
– Loosen the sleeve nut with the open-end spanner 20 by
the spanner flats 5. Adjust the angled drive head 3 in 45°
Bosch Power Tools