Andis DBLC-2 Manual de Instruções de Utilização e Cuidados - Página 4
Procurar online ou descarregar pdf Manual de Instruções de Utilização e Cuidados para Equipamento comercial para alimentos Andis DBLC-2. Andis DBLC-2 18 páginas.
Imprimir página
To start clipper, move power switch to ON position. To stop clipper, move power
switch back to original position (Figure G).
STAND CHARGING INDICATOR LIGHTS
When the battery is charging, the stand charging indicator light will turn red. The
stand charging indicator light will turn green when the clipper is fully charged
(Figure H). Under normal operation the indicator lights on the clipper will always
be dark when the unit is in the charger stand.
Note that the clipper or battery can be removed at any time during the charging
cycle without harming the clipper or battery.
CLIPPER INDICATOR LIGHTS (SPEED AND CHARGE LEVEL)
When the clipper is running, a green clipper indicator light means the battery has
a strong charge (Figure G). The light will turn yellow as the battery starts to run
down, indicating the battery has only a partial charge remaining. When the light
turns red, the battery may not hold enough charge to complete a large clipping
job, and should be recharged as soon as possible. If the clipper powers OFF,
move the power switch to the OFF position and place battery or clipper in the
charging stand.
Automatically powering off protects the lithium-ion battery and is not a
malfunction. The clipper will resume normal operation when it is recharged.
Your clipper is equipped with five cutting speeds. The speeds are adjusted using
the speed adjustment button on the front of the unit (Figure G). To start your
clipper, move the power switch to the ON position. To increase your blade
speed, slide the button toward the blade of the clipper. To decrease your blade
speed, slide the button away from the blade of the clipper. You will see on the
LED display that when you change the speed, the LED's adjust accordingly
(Figure I). To shut your clipper OFF, move the power switch to the OFF position.
The unit will power ON in the last speed setting you were in when you turned
the unit OFF.
Clipper Indicator Light
Clipper in Charging Stand
Fully Charged
Charging
Clipper in Use
Full Charge
Medium Charge
Low Charge
6
Charging Stand Indicator Light
Green
Red
Green
Yellow
Red
NOTE: If charging stand indicator light is flashing, dirt or debris may have
collected on the charging contacts of the clipper, battery pack and/or the
charging base, prohibiting proper electrical connection. To clean these contacts,
use a soft, dry cloth to wipe them clean. The charging stand indicator light will
turn off if the battery is too hot to charge. When the battery has cooled, normal
charging will resume.
BATTERY INDICATOR LIGHTS (CHARGE LEVEL)
When the battery is not in the clipper, press and release the charge level button
on the bottom of the battery pack (Figure J) to see the charge level indicator light.
A green light means there is sufficient charge. A red light means there is medium
to low charge (less than 15 minutes). No light means the battery requires
immediate charging.
REPLACING THE BATTERY PACK
To remove the battery pack from the clipper, press the tab on the back of the
battery pack and slide the battery out (Figure F). To replace the battery pack, slide
the battery into the clipper.
USER MAINTENANCE
The internal mechanism of your motor clipper has been permanently lubricated
by the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis Company,
or an Andis authorized service station. To find an Andis authorized service
station near you log on to www.andis.com or contact our customer service
department at 1-800-558-9441.
REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched off, then push
down on blade with one or both thumbs (Figure K) and slide blade off blade
hinge (Figure L). If your blade hinge should snap closed and is flush with the
clipper, use a small standard screw driver to pry the tongue of the hinge out
(Figure M). NOTE: Hair may accumu late in the front cavity of the housing under
the blade. If this hap pens, you can clean out the hair by brushing out the cavity
with a small brush or an old toothbrush while the blade is off the clipper.
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the
clipper (Figure L), and with the clipper turned "ON", push the blade towards the
clipper to lock into position.
7