Electrolux EHD30010P Manual do utilizador - Página 3
Procurar online ou descarregar pdf Manual do utilizador para Hob Electrolux EHD30010P. Electrolux EHD30010P 12 páginas. Ceramic glass induction hob
Também para Electrolux EHD30010P: Especificação (18 páginas)
Imprimir página
• Do not cover the ventilation space of 5 mm
between the worktop and front of the unit
below it.
Installation instructions
Before the installation , note down
this data from the rating plate:
• Model description (Modell)................
• Product number (Prod.
Nr.) ............. ....
• Serial number (Ser. Nr.) ...............
You find the rating plate of the ap-
pliance on its lower casing.
EHD30010P
220-240 V 50-60 Hz
58 GAD D9 AT
ELECTROLUX
Safety instructions
Warning! You must read these!
Make sure that the appliance is not dam-
aged because of transportation. Do not
connect a damaged appliance. If it is
necessary, speak to the supplier.
Only an authorised service technician
can install, connect or repair this appli-
ance. Use only original spare parts.
Only use built-in appliances after you as-
semble the appliance into correct built-
in units and work surfaces that align to
the standards.
Do not change the specifications or
modify this product. Risk of injury and
damage to the appliance.
Fully obey the laws, ordinances, direc-
tives and standards in force in the coun-
try where you use the appliance (safety
regulations, recycling regulations, elec-
trical safety rules etc.)!
Keep the minimum distances to other
appliances and units!
Install anti-shock protection, for exam-
ple install the drawers only with a pro-
tective floor directly below the appliance!
Protect the cut surfaces of the worktop
against moisture with a correct sealant!
Seal the appliance to the work top with
no space left with a correct sealant!
Protect the bottom of the appliance from
steam and moisture, e.g. from a dish-
washer or oven!
• The electrical mains terminal is live.
949 594 208 00
• Make electrical mains terminal free of volt-
Induction 3,7 kW
age.
3,7 kW
• Install correctly to give anti-shock protec-
tion.
• Loose and incorrect plug and socket con-
nections can make the terminal become
too hot.
• A qualified electrician must install the
clamping connections correctly.
• Use a strain relief clamp on cable.
• Use the correct mains cable of type
H05BB-F Tmax 90°C (or higher) for a sin-
gle-phase or two-phase connection.
• Replace the damaged mains cable with a
special cable (type H05BB-F Tmax 90°C;
or higher). Speak your local Service Force
Centre.
The appliance must have the electrical instal-
lation which lets you disconnect the appli-
ance from the mains at all poles with a con-
tact opening width of minimum 3 mm.
You must have correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
Sticking on the seal
• Clean the worktop in the area of the cut-
out section.
• Bond the sealing tape to the lower edge of
the cooking surface along the outer edge
of the glass ceramic. Do not extend it. Let
stay the cut ends in the middle of one side.
When you have cut it to length (add some
mm), push the two ends together.
Warning! If there is a crack on the
surface, disconnect power supply to
prevent the electric shock.
Do not install the appliance adjacent to
doors and below windows! If not, hot
cookware can be hit off the hob when
you open doors or windows.
Warning! Risk of injury from electrical
current. Carefully obey the instructions
for electrical connections.
electrolux 3