Bose Panaray LT MB24 III Manual de referência - Página 22
Procurar online ou descarregar pdf Manual de referência para Altifalantes Bose Panaray LT MB24 III. Bose Panaray LT MB24 III 40 páginas. Panaray lt series iii
Também para Bose Panaray LT MB24 III: Manual de serviço (27 páginas)
Imprimir página
Acoustical Specifications and Wiring
LT 9702
®
-III Loudspeaker Product Description
LT 9702-III speaker with grille
LT 9702-III speaker without grille
LT 9702-III speaker rear
22
The Bose
®
Panaray
®
LT 9702
shorter throw distances. The LT 9702-III loudspeaker offers an 92º horizontal by 61º vertical
dispersion pattern which is the broadest beamwidth of all the LT loudspeakers.
When arrayed correctly, LT 9702-III loudspeakers behave sonically as a large single source
of sound energy. This Coherent Wavefront provides full fidelity and even coverage at critical
mid- and high-frequencies throughout the coverage area of the array.
Each Panaray LT 9702-III loudspeaker uses two V2 mid-frequency drivers combined with a
1.4" compression driver mounted on a 90˚H x 70˚V constant directivity waveguide.
The LT 9702-III loudspeaker can be operated in a passive or bi-amplified mode.
• In passive mode, the internal passive crossover network is utilized and a single amplified
signal is connected to the loudspeaker.
• In bi-amplified mode, the mid-frequency and high-frequency drivers are accessed through
separate pins on the Neutrik NL4 connectors.
Active equalization for the LT 9702 III loudspeaker can be provided by using the Panaray
LT 9702-III EQ card or the Panaray system digital controller with presets for each Panaray
speaker and combination of speakers. A parametric equalizer can replicate the active
equalization curve on the following page, along with a high-pass filter and low pass filter as
shown.
LT 9702-III Acoustical Specifications
Power Handling
1
Impedance
Sensitivity
(at 1W @ 1m)
2
Maximum SPL
3
(pink noise @1m @ rated power)
Recommended Crossover
Frequency Range
(± 3 dB)
4
Beamwidth
(-6dB point, average 800 - 5 kHz)
How our loudspeakers are measured
1. Power Handling
Full bandwidth pink noise, meeting the IEC Standard #268-5, is applied to the loudspeaker and amplified to a level at the loud-
speaker terminals corresponding to the power handling of the loudspeaker. The loudspeaker must show no visible damage or mea-
surable loss of performance after 100 hours of continuous testing.
2. Sensitivity
Full bandwidth pink noise is applied to the loudspeaker with its active equalization curve and amplified to a level at the loudspeaker
terminals corresponding to 1 watt as referenced to the nominal impedance. The average sound pressure level (dB-SPL) is measured
at 1 meter from the speaker in an anechoic environment.
3. Maximum SPL
Full bandwidth pink noise is applied to the loudspeaker with its active equalization curve and amplified to a level at the loudspeaker
terminals corresponding to the long-term rated power handling of the speaker. The average sound pressure level (dB-SPL) is mea-
sured at 1 meter from the speaker in an anechoic environment.
4. Frequency Range
Sine waves are injected into the loudspeaker and the level is adjusted to 1 watt, as referenced to the nominal impedance, and the
level measured at 1meter. Resulting graph is smoothed by 0.05 octave-band.
®
-III loudspeaker is a mid/high-frequency device designed for
Passive
140W
8 Ω
104 dB SPL
126 dB SPL
Mid Frequency
HPF: 160 Hz, Butterworth, 4th order
LPF: 1600 Hz, Butterworth, 4th order
Internal Crossover @ 1.6 kHz
High Frequency
HPF: 1600 Hz, Butterworth, 4th order
LPF: 20 kHz, Butterworth, 4th order
Horizontal: 92°, Vertical: 61°
Bi-Amped
Mid
140W
8 Ω
105 dB SPL
104 dB SPL
127 dB SPL
123 dB SPL
180 Hz - 16 kHz
High
75W
8 Ω