Bose AmPlus 50 Manual do instalador - Página 8

Procurar online ou descarregar pdf Manual do instalador para Amplificador Bose AmPlus 50. Bose AmPlus 50 20 páginas. Business music amplifiers

Imprimir página
Bose AmPlus 50 Manual do instalador
All About The AmPlus
Figure 3
AmPlus 100 amplifier
controls
8
TM
100 Amplifier

AmPlus 100 amplifier controls

INPUTS A
INPUT
LEVEL
MODE
Ch1
Ch2
Ch1
Ch2
-6
-6
-10
-10
dual
2Ch
mono mono
-40 dB
0
-40 dB
+
-
+
-
Inputs – The amplifier comes with two balanced inputs. They can be left and right
channels from a stereo source or two distinct monophonic (mono) sources for 2-zone
applications. Two mono sources can also be "mixed" for single zone applications.
Input Mode – This switch determines how the Channel 1/Channel 2 inputs are
presented to the power amplifier section of the AmPlus 100 amplifier. There are three
possible modes.
1. In the 2-Channel/Mix position, the inputs remain separate, not summed. Channel
1 and Channel 2 level potentiometers (pots) are active in this mode. Use this
mode for:
a. Stereo (2-channel).
b. Two distinct sources in a two-zone application (2-channel), one source per zone.
c. Two distinct sources in a single bridged mono zone (Mix).
Note: In Mix mode both sources, Channel 1 and Channel 2, are presented to the
amplifier simultaneously. When the internal source mix switch is in the "mix" position
(Figure 5), the Channel 1 attenuation controls the source connected to the Channel 1
input. The Channel 2 attenuation controls the source connected to the Channel 2
input.
2. Dual Mono – The Channel 1 and Channel 2 inputs are summed to mono and
presented to the amplifiers as one mono signal. This mode may also be used
when driving a 70/100V load from the Channel 1 amplifier outputs and a Bose
Model 1B Acoustimass
"Zone 2 level adjust".
3. Mono Mode – Both inputs, Channel 1 and Channel 2, are summed to mono. Only
the Channel 1 level pot is active.
Level – Channel 1 level adjust – In 2-channel (stereo) mode, this pot affects the signal
level at the Channel 1 low impedance (4 ) outputs. In dual mono mode, it controls
the zone 1 level. In mono mode, it controls the level of all outputs.
Channel 2 level adjust – In 2-channel (stereo) mode, this pot controls the signal level
at the Channel 2 low impedance (4 ) outputs. This pot is not active in dual mono or
mono modes.
Zone 2 level adjust – This pot is active only when the input mode is dual mono. In this
mode, this pot controls the signal level at the Channel 2 low impedance outputs. This
pot is a slave to the Channel 1 pot; that is, the Channel 1 pot controls the level of both
zones in a 2-zone system. However, the zone 2 pot can be used to fine-tune the level
of the second listening zone without affecting zone 1. This pot may also be used to
fine-tune the bass level when using the AmPlus 100 amplifier to drive a 70/100V load
connected to the 70/100V output and a Model 1B Acoustimass module connected to
the Channel 2 output.
BASS
REMOTE
LINE OUTPUT
LEVEL
VOLUME
Zone 2
Ch1
Ch2
-6
ZONE 1
ZONE 2
ZONE 1
-10
0
-40 dB
0
OFF +10 OFF +10
+
-
®
module from the 4 Channel 2 amplifier outputs. See
POWER AMPLIFIER
ZONE 2
70/100V
ZONE1
ZONE 2
XFR
4-16
4-16
CT
+
-
+
- +
- +
-
70/100V
BRIDGED
®
MODE
2 Ch