Dromex DH-IF-THERMO Instruções

Procurar online ou descarregar pdf Instruções para Termómetro Dromex DH-IF-THERMO. Dromex DH-IF-THERMO 2 páginas.
Também para Dromex DH-IF-THERMO: Instruções (2 páginas)

Imprimir página

INFRARED THERMOMETER

DH-IF-THERMO

Description

Dromex® DH-IF-THERMO infrared hand held thermometer, is designed to scan

the forehead of groups of individuals or for monitoring an individual in

detection of elevated temperatures, without having to be in direct contact of

the person. This thermometer also measures temperature of objects.

The lightweight Dromex thermometer features the following:

• An automatic high temperature warning alarm, which sirens when

measurements are above 38˚C.

• One second temperature measurement results due to the high sensor

quality.

• An LED luminous display function, suitable for measuring at night (also

prevents disturbance for babies).

• One key operation.

High fever

Low fever

Normal

Red

Yellow

Green

backlight

About 1 second later, when the beep

sounds, it indicates the body

temperature has been measured. The

result of the measurement is displayed

on the screen and displayed

(red, yellow, green).

• Has a large memory capacity memory that stores up to 32 measurements,

ideal for monitoring of children and sick patients.

This scanner is suitable for use when conducting temperature checks used by

hospitals, oﬃces, airports, at home and mobile screenings.

Special Instructions

• Always read instructions before use.

• Always use a clinical thermometer when high accuracy body temperature

measurements are required.

• Always use a clinical thermometer to varify any abnormal temperature

measurements.

• For the most accurate results, readings should be conducted at ambient

room temperature of 10 to 40˚C (50 to 140˚F). If the surrounding

temperature is lower than 10˚C or higher than 40˚C, measurement accuracy

is not assured.

• Make sure the skin is dry and that no hair interferes with the measurement.

• Do not immerse the thermometer in water.

• Avoid touching and/or scratching the infrared sensor lens.

• Clean the lens area by gently blowing with compressed air and use a damp

swab to wipe the lens. Do not use any solvents to clean the lens.

• Actual conditions of use cannot be directly simulated in a test environment

therefore it is the responsibility of the end user and not the manufacturer or

supplier to determine the scanners suitability for the intended use.

Instructions for use

Measurements Notes

• If the meter has been stored in a cold or hot environment, allow it at least

30 minutes to acclimate to room temperature before making measurements.

• To prevent transmission of disease, avoid direct contact with the skin.

• After heavy exercise always wait at least 10 minutes before taking forehead

temperature readings.

• Temperature Mode settings

• With the meter ON, press "Mode" button for three seconds until to "F-1"

shown to enter the long term calibration drift correction mode. On entering

the mode, the previous temperature correction factor will appear on the

display. To make a correction, measure a known, ﬁxed temperature source.

Enter the correction mode and press the + or - buttons to change the

correction value and minimize the diﬀerence in readings. Repeat and adjust

the correction value as needed until the measurement on the meter

matches the known temperature. The mode is applied to Body Temp.

• Press the "Mode" button a second time "F-2" shown to set the alarm

temperature limit. Press the + or - buttons to change the value.

The mode is applied to Body Temp.

• Press the "Mode" button a third time "F-3" shown to set the °C/°F temperature

units. The temperature units °C or °F will be shown. Press the + or - buttons

to change the unit.

• Press the "Mode" button a forth time "F-4" shown to set the backlit status.

Press the + or - buttons to switch from ON to OFF.

• Press the "Mode" button a ﬁfth time "F-5" shown to set the laser status.

Press the + or - buttons to switch from ON to OFF.

Notice: Only when the laser head installed.

Mode Function

"+"

"-"

Default

Setting Deviation

Increase

Decrease

F-1

0°C

Value

0.1°C

Increase

Decrease

F-2

Setting Alarm Value

38.0°C

0.1°C

Setting

F-3

F°C

°C

Measurement Unit

F-4

Backlit ON/OFF

Oﬀ

F-5

Laser setting

Oﬀ

Save Save and automatic shut oﬀ

• Body Temperature Measurement

Please note that the forehead/temples must be free from sweat and

cosmetics and that taking vasoconstrictive medication and skin irritations

can distort the result when measuring temperature on the forehead.

• Press the trigger to switch the thermometer on with one beeper. The device

performs a brief self test: all elements of the display are shown for approx.

1 second. Following a successful self test with backlit (Red-Orange-Green),

• Press the "B/O" button for "Body temp" for accurate measurements in the

range of 32.0 to 42.9°C (89.6 to 109.2°F).

• Hold the meter by its handle and point it toward the surface to be measured.

Measurement distance should be <2.5cm(<1 in ).

• Press the trigger to take a temperature reading. The temperature reading

appears in the display.

If the F-4 MODE of backlit & "

"button voice ON & F-3 MODE set alarm

temperature 38.0°C:

Temperature (°C)

Temperature (°F)

Fever Teller

T<32.0

T<89.6

Green

32.0≤T≤37.5

89.6≤T≤99.5

Green

37.6≤T≤37.9

99.7≤T≤100.2

Orange

38.0≤T≤42.9

100.4≤T≤109.2

Red

T>42.9

T>109.2

Red

Notice: Red Backlit is followed alarm temperature limit (Fever alarm).

• Release the trigger and the reading will hold for approximately 15 seconds

after which thermometer will automatically shut oﬀ.

Note: Before shutting oﬀ, you can take further measurement.

• If the temperature goes above 109.2°F or 42.9°C, "Hi" will appear in the

display.

If the temperature goes below 89.6°F or 32.0°C, "Lo" will appear in the

display.

Dromex: Unit 1, 1 Blase Road, New Germany, 3620, South Africa

T. +27(31) 713 1960 E. [email protected]

www.dromex.co.za

Remark

Body mode available

Eﬀective Range: ±2°C

Body mode available

Eﬀective Range: 37.0~42.5°C

Only when the

laser head installed

Beep

Three beeps

One beep

Ten Rapid beebs

Three beeps