Foxfury Lighting Solutions 300–010 Manual do produto

Procurar online ou descarregar pdf Manual do produto para Lanterna Foxfury Lighting Solutions 300–010. Foxfury Lighting Solutions 300–010 2 páginas. Scout series

Imprimir página

Please read below before using your Scout as it relays

beneficial operating and safety information for all models.

P/N

Scout Tac (White & Red LEDs)

300–004

300–304

Scout Glow (White & Red LEDs)

300–010

Scout Tac (White LEDs)

300–310

Scout Glow (White LEDs)

300–11 1

Forensic UV 395 nm

300 –1 12

Forensic Blue 470 nm

300 –113

Forensic Cyan 495 nm

300 –114

Forensic Green 525 nm

300 –1 18

Forensic IR 850 nm

BATTERIES

The Scout Series requires three (3) AA batteries.

Acceptable battery types: Alkaline (recommended) or

Rechargeable (1.5V–1.7V)

Mixing of new and used, or different brand batteries

is not recommended as this could lead to leakage or

explosion.

BATTERY INSTALLATION & REPLACEMENT

Remove the light from the Comfort Clip (reference

"Removing light from Comfort Clip" in opposite column).

On the Battery Holder, turn the Locking Mechanism

to the "Open" position (use the top tab of the Comfort

Clip, a coin, or a large flat screwdriver).

Pull the Battery Holder away from the Light Body .

In order to overcome the seal you may need to

use a flat screwdriver to help separate the Battery

Holder from the Light Body , as the seal is can be

rather tight during first use.

Install batteries inside the Battery Holder following

polarity markings.

NOTE: Remove the plastic from inside the Battery Holder

before first use.

Test the Scout's performance by activating the Power/

Mode Switch, located on the upper portion of the front

face of the Light Body (just below the LEDs).

SCOUT SERIES PRODUCT MANUAL

NAME

CASE COLOR

POWER/MODE

SWITCH

"O"-RING

Then, reinsert the Battery Holder into the Light Body .

Turn the Locking Mechanism back to the "Close"

position.

NOTE: Inspect the "O"-Ring (located near the base of the

Black

Battery Holder) every time you replace batteries. The

Glow

"O"-Ring is necessary to create a water seal.

Black

BATTERY LIFE

Glow

P/N (300-XXX)

-004, -010, -111, -112, -113,

Black

-114, -118, -304, -310

*Battery life may vary according to mode selected, battery quality and

prevailing ambient conditions.

OPERATIONAL MODES

FOR P/N 300 - 010 & 300 - 310:

ALL LEDs: 2 clicks, all 10 LEDs ON

LOW mode: 1 click, outer 2 LEDs ON

FOR P/N 300- 004 & 300 -304:

ALL LEDs: 4 clicks, all 10 LEDs ON

FLASHING mode: 3 clicks, alternating white &

red LEDs

WHITE LEDs ONL Y : 2 clicks, top 6 white LEDs ON

RED LEDs ONL Y : 1 click, bottom 4 red LEDs ON

FOR P/N 300-111, -112, -113, -114 & 300-118:

ON/OFF mode: 1 click, all LEDs ON

NOTE: Once all LEDs are ON, power the Scout OFF by

clicking the Power/Mode Switch once. Then repeat steps

for desired mode.

REMOVING LIGHT FROM COMFORT CLIP

DO NOT pull upward on the light when attempting

to remove it from the Comfort Clip. Instead, pull

forward, disengaging the unit from the side clips that

encompass it. Then, pull light out completely .

To return the light to the Comfort Clip, place the

bottom of the light within the bottom of the Clip and

push inward until the light snaps in place.

BATTERY LIFE

12–50 hrs