DSC WS4916 Series Instruções de instalação e de utilização - Página 2
Procurar online ou descarregar pdf Instruções de instalação e de utilização para Alarme de fumo DSC WS4916 Series. DSC WS4916 Series 4 páginas. Wireless smoke deteçtér
Também para DSC WS4916 Series: Manual de Instruções de Instalação e Operação (8 páginas), Manual de instruções de instalação e funcionamento (9 páginas), Manual de instruções de instalação e funcionamento (8 páginas), Manual do utilizador e instruções de instalação (17 páginas), Manual de instruções de instalação e funcionamento (8 páginas)
Imprimir página
Do NOT locate smoke detectors at the top of peaked or gabled
ceilings; the dead air space in these locations may prevent the
unit from detecting smoke. Avoid areas with turbulent air flow,
such as near doors, fans or windows. Rapid air movement
around the detector may prevent smoke from entering the unit.
Do NOT locate detectors in areas of high humidity.
Do NOT locate detectors in areas where the temperature rises
above 38ºC (100ºF) or falls below 5ºC (41ºF).
2. Mount Smoke Detector Backplate
Locking
Tab
Mounting Holes
3. Install Batteries
3V CR123A
Insert
3V CR123A
Last
Insert
First
PULL
DOWN
Tab
alignment marks. Press the detector gently in place while
rotating the detector clockwise until the detector snaps into
place. Remove the side tab from the locking tab to lock in
place (optional).
• Removal: Depress tab with a
small slotted screwdriver. Rotate
detector counter-clockwise until
the alignment marks line up.
Remove detector.
Install Smoke detectors in accor-
dance with NFPA 72, Chapter 11.
"Smoke detectors shall be installed
outside of each sleeping area in
the immediate vicinity of the bed-
rooms and on each additional
story of the family living unit,
including basements and exclud-
ing crawl spaces and unfinished
attics. In new construction, a
smoke detector also shall be
installed in each sleeping room."
Secure backplate to the mounting
surface using the screws provided.
CAUTION: The dust cover pro-
tects the unit when not in ser-
vice. Remove the dust cover
before use.
If batteries are not installed, install
batteries in the sequence indicated.
Use
only
approved
CR123A, Sanyo CR123A and Dura-
cell DL123A batteries. If batteries
are installed, remove the 'Pull' tab
to activate.
4. Mounting
• Detector Installation: Position
the detector on to the base plate
using the detector and base plate
Close
Tab
Open
Installer Compensation Reset
Cleaning or replacement of the smoke sensor chamber changes
the background signal/noise of the detector; this requires the
drift compensation be reset. Compensation trouble is one of the
faults indicated when the LED indicator is OFF while the sounder
is chirping.
1. Remove batteries, then short the detector battery contacts
for 5 seconds to power down unit.
2. Replace batteries to power up unit while pressing the test
button.
3. The tamper switch must not be pressed.
4. The LED will flash when 5 seconds has elapsed. Release the
test button within 2 seconds of the LED flash.
5. The LED will flash every 2 seconds for 1 minute. During this
period, the detector must be mounted.
Allow an additional 2 minutes for the detector to
make background level checks.
6. Test the detector to verify normal operation.
5. Test Unit
NOTE: The central monitoring station (if used) should be notified
prior to the test being generated. This will prevent a false alarm
and an unnecessary response from the central monitoring station.
Initiate test by pressing the test button for 5 seconds minimum.
Alarm activation is indicated by the flashing LED, the sounder, and
transmission of the alarm signal to the control panel. The detector
restores to normal when the test button is released.
NOTE: Allow a minimum of 20 seconds after power up and ,
after test, alarm or tamper restore activations. Do not use test
button when smoke is present.
NOTE: If the detector is in one of the following states when a
test is initiated; it will not enter an alarm state.
• Tamper, (detector not installed on mounting plate)
• Compensation Trouble
Panasonic
• Other internal faults that could prevent a smoke or heat alarm.
NOTE: Smoke sensitivity of installed detectors can be measured
without removal or an alarm being generated using the FSD-100
Smoke Detector Test Meter.
To test the unit using the FSD-100, set the test meter up to read
devices as per the instructions supplied. Depress the test button
on the smoke detector for 1 second and release.
NOTE: If the test button is held for 5 seconds or longer, an alarm
will be generated.
Move the test meter over the center of the detector, wait until
you hear the test meter beep, remove the unit and the informa-
tion can be immediately reviewed. Please see the instructions
supplied with the FSD-100 Smoke Detector Test Meter for more
information.
6. Device Enrollment
The 6 digit serial number located on the back of the smoke
detector housing must be enrolled into the alarm control panel
Alignment
Marks
with Installer programming. Refer to the receiver Installation
Manual for details. For placement tests remove detector from
backplate for one second (tamper) then reattach. Wait at least
30 seconds for test result before activating again.