Atsumi Electric NR60TS Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Sensores de segurança Atsumi Electric NR60TS. Atsumi Electric NR60TS 2 páginas. Photoelectric detectors

Imprimir página

SENSITIVITY ADJUSTMENT

It is possible to adjust the detection sensitivit y by adjusting the interruption

When the unit is mounted on a wall, the interruption time can be set longer because the intruder cannot move quickly. This way,

it is possible to prevent an erroneous operation by a bird, small animal,

Adjust the sensitivity with the moving speed of a possible intruder taken into consideration. Al so, be sure to check the unit for

operation after adjustment.

OPERATION CHECK

1. Alarm Operation

To check the alarm operation, actually walk along assumed intrusion path near the transmitter

and receiver,

respectively and in-between as shown in the figure below.

Check that the alarm LED lights up and the controller receives the alarm signal when the beam

is interrupted

Transmitter

2. Tamper Operation

Check that the controller receives an abnormal signal when either of the transmitter and

receiver cover is open.

TROUBLESHOOTING

Problem

Possible cause

An obstacle exists between transmitter and receiver.

False alarm is output

frequently.

Optical axis alignment is incomplete.

Installation condition is unstable.

Distan

ce be

tween transmitter and receiver exceeds

rated distance.

Beam is interfered with beam from another detector.

There is an electrical noise source in nearby area .

Sunlight enters receiver within

There is a highly reflective wall in parallel with beam.

No ala

rm is o

utput even when

beam is interrupted

Reflectance of floor surface is high.

Beam is interfered with beam from another detector.

Height of installation position is inappropriate.

<Note>

If the trouble remains unsolved even after taking above solution, please consult the dealer of your purchase .

DIMENSIONS

Knockout

time adjustment volume.

paper and other object that flies in.

INTERRUPTION

TIME

Receiver

Solution

Remove obstacle.

Perform optical axis alignment again to obtain 1.9V

or more tester level.

Stabilize installation condition.

Change installation position or use other detector with

suitable rated distance.

Take proper measure to avoid beam interference.

Change installation position

±3°

angle.

Replace transmitter and receiver.

Adjust optical axis so that it is on the other side of

reflection surface.

Adjust optical axis so that it is on the other side of

reflection surface.

Take proper measure to avoid beam interference.

Change installation position to a proper height .

Mount plate

Mount bracket

Center of the

Upper Beam

Center of the

Lower Beam

This unit can be installed

to a pole with 38.0 to

42.7 diameter.

Scale 1

Running

Fast running at full

speed (6.9m/s)

OPTICAL AXIS ALIGNMENT

There are two ways for optical axis alignment, by using a level LED and a tester.

1. Using a level LED

Rough adjustment

While looking into the scope located in the center of the

lens 10 to 15 c m away from it, turn the turntable for adju-

stment in the horizontal direction and the vertical adju-

stment

screw for adjustment in the vertical direction until

the detector on the other side is in the center of the scope

as shown in the scope view shown below.

Rough adjustment is OK when level LED turn off.

Turntable

Vertical

adjustment

screw

SPECIFICATIONS

Product Name

Model

Power

Current Draw

Operating Temp./Humid.

Storage Temp./Humid.

Alarm Output

Max. Coverage

Sensitivity

Lens Movable Range

Installation Site

Weight

Color

MAINTENANCE

Be sure to perform periodical inspection at least annually.

Check items

• Tester level: Check that the tester level is 1.9V or more.

• Power input voltage: Check that DC

• Operation: Referring to

Scale 2

Scale 3

Fast walking

Normal walking

Walking with quick

Normal walking

steps (1.2m/s)

(0.7m/s)

2. Using a tester

Fine adjustment

Insert the tester stick into the tester hole in the receiver to check

the tester voltage.

If the measured value is 1.9V or more, adjustment is completed.

If it is less than

1.9V

ment

screw

s of the

transmitter and receiver

voltage is obtained.

1.9V～：good

Scope view

Tester

hole

Photoelectric Detector

NR30TS

NR60TS

DC10.5V

Transmitter : 15mA(at 25℃)

Transmitter : 27mA(at 25℃)

Receiver : 24mA(at 25℃)

～

-25℃

+55℃, RH 95%or less

-30℃

～

+60℃, RH 95%or less

Form 1c relay (DC30V, 0.1A) Output Period: min1.0 sec.

Alarm

Form 1b relay (DC30V, 0.1A) Retention time: While cover is opened

Tamper

30m

700m sec. (Selectable)

50 msec.

～

Horizontal direction:

Indoor / Outdoor(IP55)

Transmitter: about 380g / Receiver: about 380g

Black Mansel approximation N1.0

10.5

V to

V is obtained

OPERATION CHECK, check alarm operation and tamper operation.

Scale 4~5

Slow moving

Slow action

(0.3~0.5m/s)

adjust the horizontal and vertical adjust-

until 1.9V or more

2.2V～：execellent

NR90TS

～

28V

Transmitter : 38mA(at 25℃)

Receiver : 24mA(at 25℃)

60m

90m

°/ Vertical direction:±5°

P/N: W.97.2165 Rev.: A