3onedata ICS5400 Series Manual de instalação rápida - Página 3
Procurar online ou descarregar pdf Manual de instalação rápida para Interruptor 3onedata ICS5400 Series. 3onedata ICS5400 Series 4 páginas. Rack-mounted layer 3 industrial ethernet switch
Imprimir páginaModel V-Model VIII provides 2 AC
power sockets with switch, PWR1 and
PWR2, and supports AC power supply
input. The power input supports 1 single
power supply input or 2 power supply
inputs at the same time; When two power supply input at the
same time, it supports redundant backup of power supply. If
one power supply fails, the device can still work normally
without
interruption.
Power
110VAC/220VAC (85~264VAC).
【Relay Connection】
Provide 3-pin 5.08mm pitch terminal block,
support 1 relay alarm output. In power off
situation, R- and R+ are a group of normally
closed contacts. After powered on, the relay is
open circuit in normal non-alarm state by default, closed when
any alarm information occurs. The relay supports power
supply alarm or network abnormality alarm. It can be
connected to alarm light or alarm buzzer or other switching
value collecting devices, which can timely inform operators
when the alarm occurs.
【Console Port Connection】
Provide 1 program debugging port based on
RS-232 serial port which can conduct device CLI
command management after connecting to PC.
The interface adopts RJ45 port, the RJ45 pin definitions are
as follows:
Pin No.
2
3
Definition
TXD
RXD
【Checking LED Indicator】
Provide LED indicators to monitor its operating status, which
has simplified the overall troubleshooting process. The
function of each LED is described in the table below:
LED
Indicate
Description
ON
Power P1/2 is running normally
P1/P2
Power P1/2 is disconnected or
OFF
running abnormally
LED
ALM
RUN
supply
input
range:
LINK
(G1-24/28/32/40
, X1-X4)
【Logging in to WEB Interface】
Support WEB management and configuration. Computer can
access the device via Ethernet interface. The way of logging
in to device's configuration interface via browser is shown as
below:
Step 1
Step 2
5
GND
Step 3
Indicate
Description
Power supply or port link has
ON
alarm
Power supply, port link without
OFF
alarm
The
device
ON
abnormally
Blinking 1 time per second,
Blinking
system is running normally
The device is powered off or
OFF
the device is abnormal.
Ethernet port has established a
ON
valid network connection
Ethernet port is in an active
Blinking
network status
Ethernet
port
OFF
established
valid
connection
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed.
Enter device's IP address in the address bar of the
computer browser.
Enter device's username in the login window as
shown below.
is
running
Step 4
Click "Login" button to login to the WEB interface of
the device.
has
not
network
Note:
The default IP address of the device is "192.168.1.254".
The default username and password of the device are
"admin123".
If the username or password is lost, user can restore it to
factory settings via management software; all modified
configurations will be cleared after restoring to factory
settings, so please backup configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit copper port
Gigabit SFP
10/100/1000Base-T(X)
self-adaption or forced mode,
RJ45, Automatic Flow Control,
Full/Half
Duplex
Mode,
MDI/MDI-X Autotunning
100/1000Base-X
self-adaption
or forced mode, SFP slot