3onedata IES6300 Series Manual de instalação rápida - Página 4
Procurar online ou descarregar pdf Manual de instalação rápida para Interruptor 3onedata IES6300 Series. 3onedata IES6300 Series 4 páginas. Managed industrial ethernet switch
Também para 3onedata IES6300 Series: Manual de instalação rápida (5 páginas)
Imprimir página
I/O
has
OFF
information, and it's status is
off.
【Logging in to WEB Interface】
This series of devices supports WEB management and
configuration, and computers can access devices through
Ethernet interfaces. The way of logging in to device's
configuration interface via IE browser is shown as below:
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Enter device's IP address in the address bar of the
computer browser: https://192.168.1.254
Enter device's username and password in the login
window as shown below.
Click the "login" button. Change the initial password
when logging into the device for the first time, after
that, relog into the device to access the device's Web
interface.
Note:
The default IP address of the device is "192.168.1.254".
The default user name and password of the device are
"admin".
When logging in to the device for the first time, the
system will prompt to change the initial password of the
no
output
alarm
default user; The length of the new password string must
be greater than or equal to 8 and be composed of two or
more kinds of uppercase letters, lowercase letters,
numbers and special characters.
If the user name or password is lost, the factory settings
can be restored through management software of the
device; or make a physical loopback between Port 1 and
Port 2 within the first minute when the switch restarts.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit PoE copper port
Gigabit copper port
Gigabit SFP slot
2.5G SFP slot
I/O port
Console port
Alarm interface
10/100/1000Base-T(X), RJ45,
Automatic Flow Control, Full/Half
Duplex Mode, MDI/MDI-X
Autotunning. PoE power supply
pin: V+, V+, V-, V- correspond to
pin 1, 2, 3, 6. The maximum
output power of single port: 30W
10/100/1000Base-T(X),
RJ45,
Automatic Flow Control, Full/Half
Duplex
Mode,
MDI/MDI-X
Autotunning
100/1000Base-X self-adaption or
forced mode, SFP slot
100/1000/2.5GBase-X self-
adaption or forced mode, SFP slot
Support 2 inputs and 2 outputs, 8-
pin 3.81mm pitch terminal blocks,
support dry contact input relay
output
CLI command management port
(RS-232), RJ45
6-pin
5.08mm
pitch
terminal
blocks, alarm occupies the right 2
pins, supports 1 relay alarm
information output, and the current
load capacity is 1A@30VDC or
0.3A@125VAC
Indicator
Running indicator, alarm indicator,
power supply indicator, interface
indicator, PoE indicator, I/O output
indicator, I/O input indicator
Switch Property
Backplane bandwidth
30G
Packet buffer size
4Mbit
MAC Address Table
8K
Power Supply
Access terminal block
6-pin
5.08mm
blocks, power supply occupies 4
pins
Model I, V, IX: 12~48VDC,
non-polarity,
backup,
overcurrent protection
Model II, VI: 24VDC PoE,
anti-reverse
Power input
redundant backup, built-in 5A
overcurrent protection
Model III, VII, X: 48VDC PoE,
anti-reverse
redundant backup, built-in 5A
overcurrent protection
Model IV, VIII: 220VAC/DC
Power Consumption
No-load
≤5.76W@48VDC
Full-load
≤ 12W@48VDC (without PoE
load)
≤ 132W@24VDC (with 120W PoE
load)
≤ 252W@48VDC (with 240W PoE
load)
Working Environment
Working temperature
-40~75℃
Storage temperature
-40~85℃
Working humidity
5%～95% (no condensation)
Protection grade
IP40 (metal shell)
pitch
terminal
redundant
built-in
3A
connection,
connection,