3onedata IES7112G-4GS Manual do utilizador - Página 4
Procurar online ou descarregar pdf Manual do utilizador para Interruptor 3onedata IES7112G-4GS. 3onedata IES7112G-4GS 5 páginas. Managed industrial ethernet switch
Imprimir página
5. Environment: working temperature: -40 75
Storage Temperature: -40 85
Relative humidity 5% 95%
DIN Rail Installation
In order to use in industrial environments expediently, the product
adopt 35mm DIN-Rail installation, the installation steps as below:
1. Examine the DIN-Rail attachment
2. Examine DIN Rail whether be firm and the position is
suitability or not.
3. Insert the top of the DIN-Rail into the slot just below the
stiff metal spring.
4. The DIN-Rail attachment unit will snap into place as shown
below.
Wiring Requirements
Cable laying need to meet the following requirements,
1. It is needed to check whether the type, quantity and
specification of cable match the requirement before cable
laying;
2. It is needed to check the cable is damaged or not, factory
records and quality assurance booklet before cable laying;
3. The required cable specification, quantity, direction and
laying position need to match construction requirements, and
cable length depends on actual position;
4. All the cable cannot have break-down and terminal in the
middle;
5. Cables should be straight in the hallways and turning;
6. Cable should be straight in the groove, and cannot beyond the
groove in case of holding back the inlet and outlet holes.
Cables should be banded and fixed when they are out of the
groove;
7. User cable should be separated from the power lines. Cables,
power lines and grounding lines cannot be overlapped and
mixed when they are in the same groove road. When cable is
too long, it cannot hold down other cable, but structure in the
middle of alignment rack;
8. Pigtail cannot be tied and swerved as less as possible.
Swerving radius cannot be too small (small swerving causes
terrible loss of link). Its banding should be moderate, not too
tight, and should be separated from other cables;
9. It should have corresponding simple signal at both sides of the
cable for maintaining.
Specification
Technology
Standard: Support IEEE802.3, IEEE802.3u, IEEE802.3z/ab,
IEEE802.3x, IEEE802.1Q, IEEE802.1p, IEEE802.1W/D,
IEEE802.1s, IEEE802.3ad, IEEE802.1X
Protocol: ARP, ICMP, TCP, DHCP, DNS, HTTP, Telnet, SW-Ring,
RSTP, MSTP, LLDP, SSH, LACP, ACL, IGMP, GMRP,
SNMP
Flow control: IEEE802.3x flow control, back press flow control
Function
Switch function: SW-Ring, QOS, 802.1QVLAN, RSTP, MSTP,
LLDP, LACP, ACL, ROMN, GMRP, IGMP Snooping, SNMP,
Port trunking, static multicast filter, port mirroring, bandwidth
management, broadcast storm control, port flow statistics,
upgrade online, up and download configuration file, user
name access system
SW-Ring: Support Single, Couple, Chain, Dual homing
Exchange attribute
100M forward speed: 148810pps
1000M forward speed: 1488100pps
- 4 -
Transmit mode: store and forward
System exchange bandwidth: 24G
MAC address table: 8K
Memory: 4M
Interface
Gigabit RJ45 port: 10Base-T/100Base-TX/1000Base-TX auto
speed control, Half/full duplex and MDI/MDI-X auto detect
Gigabit SFP port: 1000Base-X, SFP slot
Console port: debug serial port carry out CLI command
Alarm port: 2 bit terminal block
1 channel relay alarm output
Transfer distance
Twisted cable: 100M (standard CAT5/CAT5e cable)
Multi-mode: 1310nm, 2Km
Single-mode: 1310nm, 20/40Km
1550nm, 60/80/100/120Km
LED indicator
Run indicator: RUN
Interface indicator: Link (G1~G12)
Power supply indicator: P1, P2
Alarm indicator: AlARM
Power supply
Input Voltage: 12 48VDC
Type of input: 4 bits terminal block
DC support reverse connection
DC support redundant power supply
Consumption
No-load consumption: 4.35W@24VDC
Full-load consumption: 9.56W@24VDC
Working environment
Working temperature: -40 75
Storage temperature: -40 85
Relative Humidity: 5%~95 %( no condensation)
Mechanical Structure