Auber WS-1500FXL Manual de operação e instruções

Procurar online ou descarregar pdf Manual de operação e instruções para Controlador Auber WS-1500FXL. Auber WS-1500FXL 3 páginas. High precision deluxe sous vide cooking controller

Imprimir página

AUBER INSTRUMENTS

Instruction Manual

High Precision Deluxe Sous Vide Cooking Controller

Introduction

Thank you for purchasing the Auber WS series temperature

controller. We sincerely appreciate your decision and trust that our

machine will meet your expectations in both the quality of the result and

the value of our product. While we are delighted that you may be

anxious to operate the controller for your project, a few minutes of your

time reading through this manual will only serve to enhance your

experience in the months and years ahead. In particular, we urge you to

read through the safety warnings below. Although this plug-and-play

controller is very easy to operate, the process involves high temperature

and high wattage appliances, and your safety is paramount.

SAFETY WARNINGS



This controller is designed only to be used with devices that have

limited power and their own thermal cutoff protection, such as a

thermostat or thermal fuse in case of controller failure.



Do not place any objects on the top of controller surface which is

used to vent excess heat during its operation.



The maximum electric current this controller can handle is 15

ampere. For 120 volt AC in US and Canada, this limits the heater

power to1800 watts.



Always place the sensor in the controlled subject when the

controller is on. Before turning on the controller, please make sure

the sensor is placed inside the container to be controlled. Leaving

the sensor outside will form an open loop operation. If the sensor is

left outside, the controller will assume the temperature is low even if

the controlled subject is already very hot. The controller will provide

full power to the heater. It will not only overheat the controller, but

also damage your appliance possibly causing a fire. If the sensor is

not permanently mounted on the system and is left outside of the

system, this could become a potential problem.



This controller is designed to control the devices recommended by

Auber Instruments only. Using it to control a not recommended

device can be dangerous and cause fire. Auber Instruments is not

liable for damages caused by misuse of the controller. If you are

not sure the controller can be used, please contact Auber

Instruments before use.



If an abnormal display or noise is observed, turn the controller off,

unplug the power cord and contact the manufacturer before using it

again.



Clean the controller only when it is cool and unplugged.



Do not allow children to operate the controller.

2014.02

Operation Instruction Manual

WS-1500FXL

Version 1.1

1. Specifications

Input voltage: 100 to 240 VAC 50 /60 Hz

Output voltage: Same as the input.

Maximum Current: 15A

Fuse Size:15A Fast blow.

Control Action: Heating (reversed action) or cooling (direct action)

Control Mode: PID, PI, PD, P or On/off

Output switching device:

Built-in optically isolated SSR with zero voltage crossing switch

Sensor type: Pt100 RTD sensor

Sensor tip dimensions: 4 mm diameter x 40 mm long.

Sensor cable length: 3 ft (915 mm)

Alarm: High And low limit alarm.

Temperature resolution: 0.1 ° C or 0.1 ° F

Temperature display range: -50 to 400 ° C or -58 to 752 ° F

Temperature accuracy: 0.2° C (0.3° F),

Dimension: 6x3.7x9.8 inch (155 x95x245 mm) W x H x D.

Weight: 4.0lb (1.8 kg)

Warranty: 1 year for controller and sensor

2. Operating Instructions

process

10.

WWW.AUBERINS.COM

Figure 1. Front Panel

Alarm 1

Alarm 2

AT/M- On for manual mode. Blinking during auto-tuning

OUT- SSR output indicator

Value increment/Select next parameter

Value decrement/Select previous parameter

Auto tuning/Digit shift

Set/Confirm/Manual Auto switching

Measured temperature, or, Process Value (PV)

Set temperature, or, Set Value (SV)

P1/3