Auburn Gear Power Wheel 350 Manual de serviço - Página 2

Procurar online ou descarregar pdf Manual de serviço para Sistema de microfone Auburn Gear Power Wheel 350. Auburn Gear Power Wheel 350 8 páginas. Double reduction shaft and spindle output drives

Imprimir página

IMPORTANT: All Power Wheel units and kits are shipped with a label that includes the Auburn Gear part number, order code and work order.

Power Wheel

Example:

ASSY. CODE

6 0 0 0 3 6 4 0

2 5 0 S D1 3 4 0 F 1 Z

3 5 0 5 7 2 0 0 1

SERIAL NO.

MH6 3 2

STEP 1

Remove twenty-four hex head bolts (20) and washers (19) from cover

(17). Thrust washer (16) usually remains with cover.

STEP 2

Lift sun gear (15) from primary carrier assembly (14).

STEP 3

Remove primary carrier assembly (14) from ring gear (7).

STEP 4

Remove ring gear (7) from hub (6). It may be necessary to

strike ring gear (7) with a rubber mallet to loosen from hub (6).

STEP 5

Remove the secondary carrier assembly (13).

STEP 6

One tab of lock washer (11) will be engaged in slot of bearing nut (12);

bend tab back to release. Remove the bearing nut (12), lock washer

(11) and thrust washer (10). NOTE: A special locknut wrench,

AG21308, is required for the removal of the bearing locknut. Contact

Auburn Gear to purchase wrench and other service tools. Drawings

are also attached.

STEP 1

Press new bearing cups (5 & 9) in each side of the hub (6). It is

recommended that bearing cups (5 & 9) and cones (4 & 8) be

replaced in sets.

STEP 2

Assemble bearing cone (4) into cup (5) at seal end of hub (6) and

press a new seal (3) into hub (6). Install boot seal (2) on hub (6) if

unit is so equipped.

STEP 3

Position output shaft or spindle (1) upright on bench. Lubricate lips

of seals (2) and (3), seal surface of output shaft or spindle, and

lower hub (6) onto output shaft or spindle (1). Hub (6) should be

centered as it is lowered over output shaft or spindle (1) to prevent

seal damage. NOTE: On heavy duty seals (order code T) there is to

be no lubricant on seal (3), output shaft or spindle (1),

or hub (6).

STEP 4

Press inner bearing cone (8) onto shaft (1) until rollers just contact

inner bearing cup (9) using a cylinder that is in full contact with the

ID of the bearing cone (see photo below).

MH749-0817

When ordering parts, the information included on the label or the stamped identification number is

AUBURN, IN U.S.A.

necessary to accurately identify the drive and obtain the correct replacement parts. Once this

information has been obtained, contact Auburn Gear for the appropriate parts list.

DISASSEMBLY OF POWER WHEEL

ASSEMBLY OF POWER WHEEL

IDENTIFICATION

In addition to the label, Power Wheel drives are stamped with an identification number

and date code, which appears on the cover or hub flange as shown.

Example: 60003640, 16 253

STEP 7

Place assembly in press with output shaft or spindle (1) down on hub

flange (6). Place material under output shaft or spindle so not to

damage when it's pressed out of hub. Care should be taken to avoid

damaging splines and threads on output shaft or spindle while pressing

it out. NOTE

respect to output shaft or spindle (1). Considerable force will be

required to remove cone from output shaft or spindle.

If a press is not available you will need the AGXXXXX(Contact Auburn

Gear) Spindle/Shaft removal tool. Place the small disk on the end of

the spindle/shaft. Mount the cross tube to the hub. Turn the screw

against the small disk, DO NOT use an impact gun. Turning the screw

will force the spindle/shaft out of the bearing cone.

STEP 8

Remove the oil seal (3) & boot seal (2), if included and bearing cones

(4 & 8) from hub (6). Inspect bearing cups (5 & 9) in position and

remove only if replacement is required.

STEP 5

Install tab of thrust washer (10) into slot of output shaft or spindle

(1). Place lock washer (11) onto output shaft or spindle (1).

STEP 6

Torque bearing nut (12) to 50 lb ft using tool AG21308.

STEP 7

Rotate hub several revolutions in each direction to allow bearings to

seat.

STEP 8

Using an appropriate pick, check each roller of the inner bearing

cone (8) for looseness.

STEP 9

If all rollers are tight, proceed to step 12.

STEP 10

With bearing nut tool AG21308 placed on bearing nut (12), tap end

of bearing nut tool with an appropriate hammer to advance the inner

bearing cone (8) further onto shaft (1).

STEP 11

Repeat steps 7 thru 10 until all inner bearing cone rollers are tight.

Bearing cone (8) has been designed with a press fit with